You are here

Cypress Traveo™ II for Body CYT2B6 Series | Cypress Semiconductor

Cypress Traveo™ II for Body CYT2B6 Series

Cypress’ Traveo II CYT2B6 series MCUs are designed for automotive body electronics with processing power and network connectivity built into the Arm® Cortex®-M4F. These devices are designed for automotive body applications such as body control modules, HVAC, and lighting.

Traveo II devices have advanced security features with the introduction of HSM (Hardware security module), dedicated Cortex®-M0+ for secure processing, and embedded flash in dual bank mode for FOTA requirements.

This family features six power modes that enable ECUs to minimize overall power consumption and cutting-edge security features for secure communication with the great scalability in memory size and pin count.

Our MCUs come with optimized software platform that is available for Cypress AUTOSAR MCAL (Microcontroller Abstraction Layer), self-test libraries, Flash EEPROM emulation, as well as security low level drivers, combined with third-party firmware.

Block Diagram:

32-bit MCU Core Systems

  • 80-MHz Arm® Cortex®-M4F Single
  • 512KB code flash, 96 KB work flash and 64 KB SRAM and Arm® Cortex®-M0+

Connectivity

  • Up to 4-ch CAN FD and up to 6-ch serial communication block (SCB) and 5-ch LIN/UART

A/D Converter

  • Up to 32-ch, 12-bit with 3x successive approximation ADC (SAR ADC) units

Timers

  • 46-ch 16 bit and 2-ch 32-bit Timer Counter Pulse Width Modulator (TCPWM)
  • Real Time Clock (RTC)
  • Event generation timer

GPIOs

  • Up to 78 Programmable GPIOs

Safety and Security

  • Embedded eSHE (Enhanced Secure Hardware Extension), HSM (Hardware Security Module) and hardware-accelerated cryptography engine (on/off option)*
  • One Time Programmable Fuses (OTP) to manage device lifecycle
  • Memory protection unit (MPU), shared memory protection unit (SMPU) and peripheral protection unit (PPU) for memory and peripheral protection
  • Support JTAG security for secure debugging
  • Safety features: ECC for memory, monitors for power supply voltage and clock

Packages

  • 100/80/64 LQFP

Temperature Range

  • -40 to 105°C (S-grade)
  • -40 to 125°C (E-grade)

*Firmware solution available include Cypress’ Security Low Level Driver and third-party firmware

Getting Started with the Traveo II


Evaluate the Traveo II

 

CYTVII-B-E-1M-SK Traveo II Low-Cost, Arduino Compatible Evaluation Board

The CYTVII-B-E-1M-SK is a low-cost easy to use evaluation board based on the Traveo II body entry family of devices. It is designed in an Arduino form factor so that users can connect many off-the-shelf Arduino shields to it, to expand its functionality.

  • Traveo II CYT2B7 series Flash 1M 100pin LQFP Device
  • On-board programming and debug interface using Kitprog3
  • High Speed CAN Transceiver
  • USB to UART bridge
  • User switch, LED and potentiometer
  • Arduino-style headers for connecting many off-the-shelf Arduino shields

Learn More

CYTVII-B-E-1M-SK Traveo II Low-Cost, Arduino Compatible Evaluation Board

 

 

CYTVII-B-E-BB Traveo II Base Body Evaluation Board

The CYTVII-B-E-BB is a generic base board that can be connected to compatible Traveo™ II body-entry or body-high evaluation boards so as to extend the functionality offered by the evaluation board.

  • Connects to most CYTVII-B-E-xxx and CYTVII-B-H-xxx evaluation boards
  • Ten high-speed CAN transceives and six LIN transceivers
  • One EEPROM device with SPI interface
  • User switches, user LEDs, and potentiometer on-board
  • Two FlexRay interfaces
  • One CXPI transceiver
  • Generic 10x2 IO headers to expand the functionality of Traveo II evaluation boards

Learn More

CYTVII-B-E-BB Traveo II Base Body Evaluation Board

 

 

CYTVII-B-E-100-SO Traveo II Socketed Body Evaluation Board

The CYTVII-B-E-100-SO, a 100-pin, socketed evaluation board is based on the Traveo II body entry family of devices. The socket is provided such that the users can replace the microcontroller of the same pin configuration available in the family.

  • 100 PIN Socket supports Traveo II CYT2B7 series Flash 1M 100pin LQFP Device
  • Programming interface (Arm® Standard JTAG, Cortex® Debug, Cortex Debug + ETM and Arm ETM Mictor) to connect several programming tools such as IAR I-jet, Green Hills MULTI, also MiniProg
  • Reset controller with manual reset switch and voltage supervision
  • One user switch and one user LED
  • Samtec connector interfacefor connecting to the base board CYTVII-B-E-BB
  • USB to UART bridge

Learn More

CYTVII-B-E-100-SO Traveo II Socketed Body Evaluation Board

 

 

Traveo II Sample Driver Library

Infineon’s Sample Driver Library (SDL) simplifies software development for Traveo II devices

  • Drivers for the extensive set of peripherals supported
  • Arm® Cortex® Microcontroller Software Interface Standard (CMSIS) core access header files directly from the CMSIS 5.0 release
  • CMSIS complaint device header files, startup code (platform initialization), and device configuration header files
  • SDL Application Programming Interface Reference Manual
  • Examples to evaluate various peripherals

Learn More

Traveo II Sample Driver Library Logo

 

 

Traveo II Auto Flash Utility

Auto Flash Utility is a stand-alone flash programmer tool which supports Traveo II MCUs and provides programming functionality via MiniProg4 and J-Link probes. This tool is based on OpenOCD open source.

Learn More

Traveo II Auto Flash Utility Logo

 

Traveo II Sample Driver Library

Infineon’s Sample Driver Library (SDL) simplifies software development for Traveo II devices

  • Drivers for the extensive set of peripherals supported
  • Arm® Cortex® Microcontroller Software Interface Standard (CMSIS) core access header files directly from the CMSIS 5.0 release
  • CMSIS complaint device header files, startup code (platform initialization), and device configuration header files
  • SDL Application Programming Interface Reference Manual
  • Examples to evaluate various peripherals
Traveo II Sample Driver Library Icon

 

Traveo II Auto Flash Utility

Auto Flash Utility is a stand-alone flash programmer tool which supports Traveo II MCUs and provides programming functionality via MiniProg4 and J-Link probes. This tool is based on OpenOCD open source.

Traveo II Auto Flash Utility Icon

 

Infineon Development Kits

CYTVII-B-E-1M-SK

CYTVII-B-E-1M-SK

Development Kits

The CYTVII-B-E-1M-SK is a low-cost easy to use evaluation board based on the Traveo II body entry family of devices. It is designed in an Arduino form factor so that users can connect many off-the-shelf Arduino shields to it, to expand its functionality.

CYTVII-B-E-BB

CYTVII-B-E-BB

Development Kits

The CYTVII-B-E-BB is a generic base board that can be connected to compatible Traveo™ II body-entry or body-high evaluation boards so as to extend the functionality offered by the evaluation board.

CYTVII-B-E-100-SO

CYTVII-B-E-100-SO

Development Kits

The CYTVII-B-E-100-SO, a 100-pin, socketed evaluation board is based on the Traveo II body entry family of devices. The socket is provided such that the users can replace the microcontroller of the same pin configuration available in the family.

Cypress Developer Community Banner

Traveo II Customer Training Workshops