SK-FM3-80PMC-9BF524M-JL | Cypress Semiconductor
This development kit is no longer available. This web page has been left in place for informational purposes only.
Supports MB9B120M, MB9B320M and MB9B520M Series
The SK-FM3-80PMC-MB9BF524M is a multifunctional evaluation board, including a Segger J-Link JTAG adapter, for the Cypress microcontroller of the MB9B120M, MB9B320M, and MB9B520M Series.
The board allows the designer immediately to start software development before his own final target system is available.
Contents of the kit:
- Starterkit SK-FM3-80PMC-MB9BF524M incl. MB9BF524MPMC (max. 72MHz)
- J-Link - JTAG adapter with USB interface
- Software Examples
- Development Tools
- The SK-FM3-80PMC-MB9BF524M is a multifunctional evaluation board for the Cypress microcontroller of the MB9B120M, MB9B320M, and MB9B520M Series.
- Power supply via USB (UART"B"), USB-Device, JTAG or external with a 8V to 12V power connector
- On-board 5.0V and 3.3V voltage regulator
- Two 7-Segment LED-Displays
- Reset button, Reset LED
- Two user buttons
- In-Circuit Flash programming (UART, USB, JTAG)
- All MCU pins routed to edge connectors
- All resources available for evaluation
- 4 MHz main crystal
- RS232 interface (SUB-D9 connector)
- USB to serial converter (Type-B connector)
- CAN interface (SUB-D9 connector)
- USB Host (Type-A) and Device (Type-B) connectors
- JTAG and ETM interface
- TSC-Interface to connect for example the Cypress SK-TSC-1127S-SB
- RoHS compliant
- CE conform
|Complete Driver, Documentation, Software & Tools package (v1.1)||SK-FM3-48PMC-MB9BF524K_+_SK-FM3-80PMC-MB9BF524M_CD.zip|
|Tools (contains Cypress Serial Port Viewer and Flash MCU programmer)||SK-FM3-48PMC-MB9BF524K_tools.zip|
|Drivers (contains USB-Virtual-COM-port (VCP) driver (see http://www.ftdichip.com/Drivers/VCP.htm for latest version), CMSIS-DAP debugging and Direct Flash programming)||SK-FM3-48PMC-MB9BF524K_drivers.zip|
SK-FM3-80PMC-9BF524M-JL - SOFTWARE EXAMPLES
The following software is for demonstration purposes only. It is not fully tested, nor validated in order to fulfill its task under all circumstances. Therefore, this software or any part of it must only be used in an evaluation laboratory environment.
Use only the template-project as starting point for your application. Only the template-project will be updated in case of any change of the header files, startup code etc.!
|Tool specific Software Examples|
|Template project for MB9BF52xM||mb9bf52xm_template.zip (v1.4)|
|A simple digital voltage meter (DVM). The analog value on pin AN24 (pin 4) is measured by the ADC Modul. The conversion result is displayed alternately on the 7 segment display as hex value and as voltage value. (Only integer part)||mb9bf52xm_adc_dvm-E.zip (v1.1)|
|The CAN_UART example show functionality of the CAN-controller (CAN1_2).The program is controled by a PC-terminal-program via UART0 (115200Baud)||mb9bf52xm_can_uart_terminal-E.zip (v1.1)|
|A decimal counter is realized by Port 5 and Port 3 controlling two 7-segment displays. After reset the display will start from '00' counting up until '99'. The count direction can be changed by SW2/NMIX/WKUP0 (down) and SW3/INT21_1 (up).||mb9bf52xm_ioport_counter-E.zip (v1.1)|
|This example initializes the Multifunctional Serial Interface 0 (UART 0) to asynchronous 8N1 format at 115,2 k Bits/s. No interrupts are used.A welcome string is output and any received character is echoed by output.||mb9bf52xm_uart-E.zip (v1.1)|
|This example initializes the Multifunctional Serial Interface 0 (UART 0) to asynchronous 8N1 format at 115,2 k Bits/s. For reception the RX interrupt of UART 0 (MFS0) is used||mb9bf52xm_uart_irq-E.zip (v1.1)|
|USB Host Mass Storage bootloader for FM3 flashing motorrola S-Record file 9bf524m.mhx or app.mhx located on an USB stick into user code area starting linked to 0x00004000. This bootloader is for use with SK-FM3-80PMC-MB9BF524M, MB9BF524M MCU.||mb9bf52xm_usbhost_msd_bootloader.zip (v1.0)|
|Serial Port Viewer and Terminal||SerialPortViewerAndTerminalV57.zip|