You are here

The Lost Art of Assembly Language Programming | Cypress Semiconductor

The Lost Art of Assembly Language Programming

[re-printed from iotexpert.com]

My friend Darrin Vallis - renowned semiconductor maven and part time wookie-hunter (don't ask!!) - guest-blogs on Alan's iotexpert site about assembler programming on PSoC devices.

Cypress introduced it’s first mass market microcontroller in 2001. It used a Cypress designed 8 bit CISC processor running at 24 MHz, with as little as 4 KB Flash and 256 bytes RAM. Wrapped around that was a neat array of programmable analog and digital blocks. This may not sound like much, but with a creative mindset you could get these parts to do amazing things. For instance, I once implemented a complete ultrasonic ranging sensor with full wave analog demodulation in a single PSOC1 as shown below.

PSoC 1 Ultrasonic Ranging

With CPU resources at a premium, you had to write tight, efficient code to get the most out of PSOC1. A single C library could consume the entire Flash. Consequently, I wrote a lot of assembly code. That’s not so bad, since I actually enjoy it more than C. There’s a certain elegance to well written, fully commented machine code. In the case of PSOC1, here’s what you had to work with: 5 registers, some RAM and Flash. That’s it. Real Men Write In Assembly.

M8C Architecture

We’ll start with simple machine code instruction to make the CPU do something. You can reference the M8C assembly language user guide here for more details. To get the M8C to execute 2+3=5 we write:

mov A,2       ;Load A with 2

add A,3       ;Add 3 to A. Result=5 is in A

We can get fancy by using variables. Let’s add R=P+Q. Assume P is at RAM location 0x20 and Q is at location 0x21, and R is at 0x22

;Initialize variables

mov [0x20],2  ;Load P with 2

mov [0x21],3  ;Load Q with 3

;Add variables

mov X,[0x20]  ;X <- P

mov A,[0x21]  ;A <- Q

adc [X],A     ;X <- P + Q

mov [0x22],X  ;R <- X

The fun thing about assembly is you can always dream up cool ways of doing things in less operations based on the machine’s instruction set. For example, we can simplify the above code as follows:

;Add variables

mov [0x20],[0x22]   ;R <- P

adc [0x22],[0x21]   ;R <- P + Q

In my experience, a good programmer with expert knowledge of the instruction set and CPU resources can always write better code than a compiler. There’s a certain human creativity that algorithms can’t match.

All that being said, I had not seen a good “machine code 101” tutorial for writing assembly in PSOC Creator on modern ARM M0 processors. So let’s walk through one now. We’ll use a CY8CKIT-145 and blink the LED. It’s just what happens to be laying around on the lab bench. Any PSoC 4 kit will do.

CY8CKIT-145-40XX

We’ll start by creating a standard project in PSOC Creator, drop a Digital Output pin on the schematic and call it “LED”

Drop a Digital Output pin on the schematic and call it “LED”

Then open the .CYDWR file and drag pin LED to P2[5], since that’s where it is on the LED board. Yours may be in a different place on whatever board you are using.

Drag pin LED to P2[5]

Now under “Source Files” in the workspace directory you will delete main.c and replace with main.s

Replace main.c with main.s

Now right clock on “Source Files”, select “Add New File” and select “GNU ARM Assembly File” in the dialog. Rename the file from GNUArmAssembly01.s to main.s

Rename the file from GNUArmAssembly01.s to main.s

Your workspace ends up looking like this:

Updated workspace

So far, so good. Now open main.s, delete everything if it’s not empty and add the following code. This sets up the IDE for M0 assembly architecture

// ==============================================

// ARM M0 Assembly Tutorial

//

// 01 – Blink LED

// ==============================================

.syntax unified

.text

.thumb

Next we need to include register definitions for the chip we are using. These are all from the PSoC 4 Technical Reference Manual (TRM)

// ==============================================

// Includes

// ==============================================

.include “cydevicegnu_trm.inc”

Then we are going to do some .equ statements, same as #define in C. This identifies the Port 2 GPIO data register plus bits for the LED pin in on and off state

// ==============================================

// Defines

// ==============================================

.equ LED_DR,CYREG_GPIO_PRT2_DR          // LED data reg address

.equ LED_PIN,5                          // P2.5

.equ LED_OFF,1<<led_pin                 // 0010 0000

.equ LED_ON,~LED_OFF                    // 1101 1111

Now you add the right syntax to set up main()

// ==============================================

// main

// ==============================================

.global main

.func main, main

.type main, %function

.thumb_func

Finally we add the code for main, which is pretty simple:

main:

ldr r5,=LED_DR      // Load GPIO port addr to r5

loop0:

ldr r6,=LED_ON      // Move led data to r6

str r6,[r5]         // Write r6 data to r5 addr

ldr r0,=0xFFFFFF    // Argument passed in r0

bl CyDelayCycles    // Delay for N cycles

ldr r6,=LED_OFF     // Move led data to r6

str r6,[r5]         // Write r6 data to r5 addr

ldr r0,=0xFFFFFF    // Argument passed in r0

bl CyDelayCycles    // Delay for N cycles

b loop0             // Branch loop0

.endfunc            // End of main

.end                // End of code

One thing to note: The function CyDelayCycles is defined CyBootAsmGnu.s. Any function in assembly gets its arguments passed by the first 4 registers r0,r1,r2 and r3. Before calling the function you simply load r0 with the argument then do a bl (branch with link). This is also why I avoided the first 4 registers when messing with LED data. If you’re interested in doing more with ARM assembly, definitely read the Cortex M0+ Technical Reference Manual. It’s a great primer for the M0+ instruction set.

End result is a blinking LED

That’s it. End result is a blinking LED. Cool thing is you can use PSOC Creator with all it’s nice features, but sill access the power of machine code.

You can get the project ZIP file here.

Regards

Darrin Vallis

Blog: 

ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.