You are here

Annotation library for CY8CKIT-059 Prototyping Kit | Cypress Semiconductor

Annotation library for CY8CKIT-059 Prototyping Kit

Summary: 9 Replies, Latest post by odissey1 on 10 Oct 2016 02:25 PM PDT
Verified Answers: 0
Last post
Log in to post new comments.
user_342122993's picture
User
582 posts

Hi,
I am uploading a library of small off-chip components for annotation of the CY8CKIT-059 PSoC 5LP Prototyping Kit.

The KIT-059 component shows all on-board capacitors and pins with direct connections to the OpAmps, DACs, SARs, I2C, UART, LED and XTAL. It helps visualizing ports and pins and making connection diagrams for CY8CKIT-059 Prototyping Kit.

The accompanying library contains few small-sized off-chip annotation components (resistor, capacitors, OpAmps, DAC, etc.). The components are about 50% smaller than their stock analogs, allowing for tighter schematic placement.

The demo project shows all-analog PID control of the levitationg globe, implemented in CY8CKIT-059 PSoC 5LP Prototyping Kit, with annotation diagram created using KIT-059 component.

Attached archive contains component library, a demo project and enlarged picture of the Prototyping Kit. Last tested under Creator 3.3 CP3.

regards,
odissey1

user_342122993's picture
User
582 posts

Attached are demo screenshots of the KIT-059 library and an example project from YouTube (levitating Globe using PSoC5) annotated using KIT-059 library:

 

user_365962704's picture
User
166 posts

Great odissey1!!! I will use them for sure :D

Carlos

user_365962704's picture
User
166 posts

Hi oddisey,

I'm trying to do some similar annotation figures (PWM, clk, etc), looking at your library i think you made the background as an separated image and then imported it to cysym file and then added the instance name over the background image, if so, by any chance do you remember the size of the grid on the cysym file? kind of painful working with the cysym to draw "freely".

Thanks in advance, i will upload the annotation figures when done.

Carlos

user_342122993's picture
User
582 posts

Actual spacing between terminal is as comes from Creator installation and is 6 a.u. (whatever units are used in FormatShape->Size->X,Y.

user_365962704's picture
User
166 posts

5mm? 5 px?

Anyway i'm at school, will try later today all the options.

Thanks for the fast reply :)

user_365962704's picture
User
166 posts

Hi odissey, i had added a couple of symbols (PWM and Clock), and changed the Component Placement option to be the same as your components, but i'm unable to find the PWM and Clock symbols on the test project :/.

Can you take a look on the attached project to see if you can find what i'm missing?

Thanks in advance

Carlos

user_342122993's picture
User
582 posts

Carlos,

Attached is updated library. Few remarks: (i) somehow your library project contains top schematics. Create library project and import into it all necessary components. (ii) If you modifying existing library, rename it (what if I continue to debug and modify the original one). (iii). This is a tough one. I created a new add-on library (attached) and imported your components. The Clock and KIT-059_FULL were visible, but PWM is not. It becomes visible if renamed to "PWM1". I tried to rename it to various other names: "ABC", "PWM_1", "PWMsm", etc. - they don't show in the catalog. Mistery. 

P.S. I will be travelling on Monday.  

user_365962704's picture
User
166 posts

Hi Odissey,

Thanks for the help, yes i will create a new library and add all the needed components. Also just realize that the Clock component is available.

Will try to do the PWM component from scratch again, and see if i can make it work.

Thanks for all the suggestions and have a good travel :D

Carlos

user_342122993's picture
User
582 posts

I actually rebuilt PWM component from SmallCap one just adding your picture. I suggest to file case support.

Log in to post new comments.