What are high z pins?
I just wanted to know what does High Z mean?? and how provides enough voltage???
"High Z" means high impedance. This is used for analog inputs, since there the impedance of the input can affect the signal level (if it is too low).
As hli said, "High Z" is for Analog Input.
Here's more info on the drive modes:
When a pin is internally connected to an analog usermodule as amplifiers, ADCs or DACs the signal is treated differently and routed within a completely different part of the chip than when the pin is connected to a digital signal internally. Hi-Z refers to the input impedance only. When routing with Creator 2.1 your usermodules you will see different colors used for the wires: green for digital signals, orange for analog signals and blue for annotation wires outside of the chip.
High Z analog drive mode should be used for any pin connected to any analog component. For eg. input of ADC, output of DACs as well as input and output of PGAs, OPAMPs.
High Z digital drive mode should be used for digital input pins when both logic levels are driven externally. For example, in UART, RX pin should be high z digital since TX on the other side will drive logic 0 as well as logic 1 on the line.
On the other hand, a pin connected to a switch which toggles between digital '0' and open circuit can not be high z digital. In this case, the drive mode should be resistive pull up to hold the voltage at logic '1' level when switch is open circuit.
Hi Z, as you can see from the schematic pic in earlier post, means
the source and sink drivers are turned off at the pin, and the pin is connected
via a route to a buffer input. So the Z is routing R + buffer C in. From an
AC point of view.
From a DC point of view HiZ means basically all you are driving/absorbing is a
leakage current, that of the buffer input and the output totem pole driver leakages.
A caution you must consider is HiZ, is if source driver is also HiZ interpreting what
will be the voltage on the pin, as this case is controlled by leakage, and device to
device variation and temp effects will produce unpredictable values. In short be
careful about HiZ pins driving, for example, a MOSFET or Bipolar. Leakage can
turn these devices on when you do not want this behaviour. So terminate a HiZ pin
under these circumstances with an R such that R x Ileak < Vth, where Vth is turnon
V of the external device.
SO , if I have my PSOC3 connected to some other device say PSoC5, now when i reset the PSoC3 will the pins drain some current from PSoC5 pins if not set to high Z configuration on reset????
The answer is YES. Pins not configured as High-Z (which is the default) will sink or source current from its connection. When resetted the pins are in Hi-Z state and the initialization of the chip starts which includes setting the pin's drive mode and polarity which will alltogether take some miliseconds.
This might help - www.cypress.com/?docID=34818
Startup and Low-Power Behavior
Out of the box, all GPIO pins start up in an Analog HI-Z state and remain in that state until reset is released. The initial operating configuration of each pin is loaded duringboot and takes effect at that time. The reset behavior of GPIOs can be changed in PSoC 3 using the PRTxRDMfields of the nonvolatile latch array, which are written when the PSoC is programmed.
In all low-power modes, GPIO pins retain their state until the part is reset or awakened. The port interrupt logic continues to function in all low-power modes so that pins can be used as wakeup sources.
Hi, Im giving variable analog input(max rating 5V) to PSoC 5lp in high impedance mode.Now my question is can I directly give the potentiometer input to PSoC?How much resistance does any analog pin provide in this mode? Will the current damage PSoC?
Right now as precaution i have connected 1k in series with POT,Psoc is taking floating value when i switch the input near to zero volts.The reason being psoc is unable to detect ground because of that 1k ohm.
Please, when you have a new question, ask it as such and open a new topic. Don't hijack a year-old thread, especially when it has nothing to do with your question. A new topic will increase your chance of getting a good answer.
Btw: it can be andwered by just reading the PSoC5 data sheet, it states the properties of the analog inputs and the maximum ratings they can withstand.