Features

• Device Operating Voltage Options:
  • MoBL Clock M200 Family: 1.8V
• Selectable clock output voltages for both MoBL Clock M200 and M500:
  • 1.5V, 1.8V, 2.5V, 3.0V, or 3.3V
• Fully integrated ultra low power phase-locked loops (PLLs)
• Input reference clock frequency range: 1–48 MHz
• Output clock frequency range: 3–50 MHz
• Three I2C™ programmable output clocks
• Programmable output drive strengths
• For more, see pdf
   

General Description

2 Configurable PLLs

The MoBL® Clock M200/M500 Family of products are two-PLL Clock Generator ICs designed for cell phone, portable, or consumer electronics applications. It can be used to generate two independent output frequencies ranging from 3 to 50MHz from a single input reference clock.

Features

• Low jitter crystal oscillator (XO)
• Less than 1 ps typical root mean square (RMS) phase jitter
• Differential low-voltage positive emitter coupled logic (LVPECL) output
• Output frequency from 50 MHz to 690 MHz
• Frequency margining through I²C bus
• Factory-configured or field-programmable
• Integrated phase-locked loop (PLL)
• Pb-free package: 5.0 × 3.2 mm leadless chip carrier (LCC)
• Supply voltage: 3.3 V or 2.5 V
• Commercial and industrial temperature ranges
   

Functional Description

The CY2XF24 is a high-performance and high-frequency XO. It uses a Cypress-proprietary low-noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed using the I2C bus serial interface, allowing easy frequency margin testing in applications.

Features

• Low Jitter Crystal Oscillator (XO)
• Less than 1 ps Typical RMS Phase Jitter
• Differential LVDS Output
• Output Frequency from 50 MHz to 690 MHz
• Two Frequency Margining Control Pins (FS0, FS1)
• Factory Configured or Field Programmable
• Integrated Phase-Locked Loop (PLL)
• Supply Voltage: 3.3V or 2.5V
• Pb-Free Package: 5.0 x 3.2 mm LCC
• Commercial and Industrial Temperature Ranges
   

Functional Description

The CY2XF33 is a high performance and high frequency Crystal Oscillator (XO). It uses a Cypress proprietary low noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed through two select pins, allowing easy frequency margin testing in applications.

The CY36800 InstaClock Universal Programmable Clock Generator Programming Kit contains the programming board with a USB cable, and 3 samples each of the CY22800 and CY22801 devices. You can order more samples of either CY22800 or CY22801 Online. The latest programming software is available to download from www.cypress.com/instaclock.

When using the CY22800 and InstaClock software, users can select from a list of over 100 different predefined configurations of commonly used frequencies in today's designs.  The CY22801 enables users to generate custom clock configurations that are not supported by the CY22800.  The CyberClocks software tool allows users to specify the XIN/CLKIN frequency, crystal load capacitance, and output frequencies for the CY22801.

Both the CY22800 and CY22801 devices are programmed through the same programming board included in this kit.  The selected configuration is then downloaded via USB to the programmer in a matter of moments.  Production quantities are easily supported by Cypress' distribution partners.  Simply provide your local distributor with the JEDEC code generated by the software.

Note: This is a programming kit only. This kit is not designed and intended to be used for device evaluation or testing purposes.

For more information, click here.

InstaClock™ CY36800 Kit Contents:

• 3 Samples of CY22800
• 3 Samples of CY22801
• 1 Programmer board with USB connector and socket onboard
• 1 USB Cable

Software Title	Description	Link
InstaClock Software	Jedec files pre-configured and Programmer software for CY22800
CyberClocks Software	Jedec file Creator and Programmer software for CY22801

Features

• Low jitter crystal oscillator (XO)
• Less than 1 ps typical root mean square (RMS) phase jitter
• Low-voltage differential signaling (LVDS) output
• Output frequency from 50 MHz to 690 MHz
• Factory-configured or field-programmable
• Integrated phase-locked loop (PLL)
• Output enable (OE) or power-down (PD#) function
• Supply voltage: 3.3 V or 2.5 V
• Pb-free package: 5.0 x 3.2 mm leadless chip carrier (LCC)
• Commercial and industrial temperature ranges
   

Functional Description

The CY2X013 is a high-performance and high-frequency XO. The device uses a Cypress proprietary low-noise PLL to synthesize the frequency from an integrated crystal.

The CY2X013 is available as a factory-configured device or as a field-programmable device. Factory-configured devices are configured for general use or they can be customer-specific.

Features

• Low jitter crystal oscillator (XO)
• Less than 1 ps typical root mean square (RMS) phase jitter
• Differential low-voltage positive emitter coupled logic (LVPECL) output
• Output frequency from 50 MHz to 690 MHz
• Factory-configured or field-programmable
• Integrated phase-locked loop (PLL)
• Output enable or power-down function
• Supply voltage: 3.3 V or 2.5 V
• Pb-free package: 5.0 x 3.2 mm leadless chip carrier (LCC)
• Commercial and industrial temperature ranges

Functional Description

The CY2X014 is a high-performance and high-frequency XO. The device uses a Cypress proprietary low-noise PLL to synthesize the frequency from an embedded crystal.

The CY2X014 is available as a factory-configured device or as a field-programmable device. Factory-configured devices are configured for general use or they can be customer specific.

Features

• Small Footprint, 8-Pin QFN 1.7 mm x 1.7 mm x 0.6 mm Package
• Low Power and Low Jitter Operation
• Multiple Operating Voltages:
  • CY22M1S: 2.5 V, 3.0 V, or 3.3 V
  • CY22M1L: 1.8 V
• Programmable Single Output Clock Generator Frequency Range:
  • 1 to 80 MHz
• Crystal or External Reference Clock Input Frequency Range:
  • Fundamental Tuned Crystal: 8 to 48 MHz
• For more, see pdf
   

Functional Description

The MoBL® UniClock CY22M1 is a programmable, high accuracy, PLL-based clock generator device designed for low power, space constrained applications. The low jitter and accurate outputs makes this device suitable for handsets, portable media players, personal navigation devices, digital cameras, digital camcorders, and other portable applications.

Features

• Low jitter crystal oscillator (XO)
• Less than 1 ps typical root mean square (RMS) phase jitter
• Low-voltage differential signaling (LVDS) output
• Output frequency from 50 MHz to 690 MHz
• Frequency margining through I2C bus
• Factory-configured or field-programmable
• Integrated phase-locked loop (PLL)
• Pb-free package: 5.0 × 3.2 mm leadless chip carrier (LCC)
• Supply voltage: 3.3 V or 2.5 V
• Commercial and industrial temperature ranges
   

Functional Description

The CY2XF23 is a high-performance and high-frequency XO. It uses a Cypress proprietary low-noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed using the I2C bus serial interface, allowing easy frequency margin testing in applications.

• Small Footprint, 8-Pin QFN 1.7 x 1.7 x 0.6 mm3 Package
• Low Power and Low Jitter Operation
• Multiple Operating Voltages:
  • CY22U1S: 2.5V, 3.0V, or 3.3V
  • CY22U1L: 1.8V
• Programmable Single Output Clock Generator Frequency Range:
  • 1 to 200 MHz
• Crystal or External Reference Clock Input Frequency Range
• For more, see pdf

Functional Description
 

Three PLL General Purpose EPROM Programmable Clock Generator

Features

• Three integrated phase locked loops (PLLs)
• Erasable programmable read only memory (EPROM) programmability
• Factory programmable (CY2292) or field programmable (CY2292F) device options
• Low-skew, low-jitter, high accuracy outputs
• Power management options (shutdown, OE, suspend)
• Frequency select option
• Smooth slewing on CPUCLK
• Configurable 3.3 V or 5 V operation
• 16-pin small-outline integrated circuit (SOIC) package (CY2292F also in TSSOP)

Operation

The CY2292 is a third-generation family of clock generators. The CY2292 is upwardly compatible with the industry standard ICD2023 and ICD2028 and continues their tradition by providing a high level of customizable features to meet the diverse clock generation needs of modern motherboards and other synchronous systems.

Features

• Three integrated phase-locked loops
• EPROM programmability
• Factory-programmable (CY2291) or field-programmable (CY2291F) device options
• Low-skew, low-jitter, high-accuracy outputs
• Power-management options (Shutdown, OE, Suspend)
• Frequency select option
• Smooth slewing on CPUCLK
• Configurable 3.3 V or 5 V operation
• 20-pin SOIC Package

Functional Description

The CY2291 is a third-generation family of clock generators. The CY2291 is upwardly compatible with the industry standard ICD2023 and ICD2028 and continues their tradition by providing a high level of customizable features to meet the diverse clock synchoronous systems.

All parts provide a highly configurable set of close for PC motherboard applications. Each of four configurable clock outputs (CLKA-CLKD) can be assigned 1 of 30 frequencies in any combination. Multiple outputs configured for the same or related[3] frequencies have low (<500 ps) skew, in effect providing on-chip buffering for heavily loaded signals.

Related Documents:

Application Note: Layout Recommendations for the CY22050 and CY22150 Devices - AN1110

• Jitter peak-peak (TYPICAL) = 35 ps
• LVPECL output
• Default Select option
• Serially-configurable multiply ratios
• Output edge-rate control
• 16-pin TSSOP
• High frequency
• 3.3V operation
• For more, see pdf
   

Features

• Integrated phase-locked loop (PLL)
• Field-Programmable
• Input frequency range:
• • Crystal: 8 MHz to 30 MHz
  • CLKIN: 1 MHz to 133 MHz
• Low-voltage complementary metal oxide semiconductor (LVCMOS) output frequency:
  • 1MHz to 200 MHz (commercial grade)
  • 1MHz to 166.6 MHz (industrial grade)
• For more, see pdf

General Description

The CY22801 is a flash-programmable clock generator that supports various applications in consumer and communications markets. The device uses the Cypress-proprietary PLL along with Spread Spectrum and VCXO technology to make it one of the most versatile clock synthesizers in the market. The device uses a Cypress-proprietary PLL to drive up to three configurable outputs in an 8-pin SOIC.

• Independent PWM control of up to eight LEDs
• PWM duty cycle granularity configurable to either 5 or 10% steps
• Configurable PWM frequency
• 0.4% CPU usage for 60 Hz PMW with 5% duty cycle granularity
• Maximum LED current is 25 mA
• Maximum total current load on the device is 120 mA (60 mA/side) as limited by device specifications
• In quasi closed loop current control mode, each LED requires two GPIO pins, one current limiting, and one current sensing resistor
• In explicit PWM duty cycle mode only one GPIO pin and a current limiting resistor are required
• Wizard for quick and easy LEDs configuration

Functional Description

The SmartLED User Module implements a “soft” PWM drive that provides the LED brightness/current control for up to eight independent LEDs. Configurable PWM duty cycle enables you to implement visual effects such as LED breathing.

Features

• Wide Operating Output (SSCLK) Frequency Range
  • 3 to 200 MHz
• Programmable Spread Spectrum with Nominal 31.5 kHz modulation Frequency
• Center Spread: ±0.25% to ±2.5%
• Down Spread: –0.5% to –5.0%
• Input Frequency Range
  • External crystal: 8 to 30 MHz fundamental crystals
  • External reference: 8 to 166 MHz clock
• Integrated Phase-Locked Loop (PLL)
• For more, see pdf
   

Description

The CY25200 is a programmable clock generator with spread spectrum capability. Spread spectrum modulates the output clock frequency over a small range, spreading the energy and reducing the energy peak. This is a powerful technique to reduce EMI in a variety of applications.

• 25 MHz to 100 MHz Operating Frequency Range
• 9 different Spread Select options
• Accepts Clock and Crystal Inputs
• Low Power Dissipation:
  • 56 mW at Fin = 25 MHz
  • 89 mW at Fin = 65 MHz
  • 139 mW at Fin = 100 MHz
• Frequency Spread Disable Function
• Center Spread Modulation
• For more, see pdf
   

Features

• Three output frequencies plus reference out
• Programmable output frequencies through two-wire serial interface
• Output frequencies from 4.9152 to 148.5 MHz
• Uses an external 27 MHz crystal or 27 MHz input clock
• Optional analog VCXO
• Programmable output drive strength to minimize EMI
• The equivalent without a serial port is the CY22388/89/91
• 16-pin TSSOP package
• 3.3 V operation with 2.5 V output buffer option

General Description

The CY24488 generates up to three independent clock frequencies, and a buffered copy of the reference crystal frequency, from a single crystal or reference input. Five clock output pins are available, which allows some frequencies to be driven on two or more output pins. Outputs can also be individually enabled or disabled. When a CLK output is individually disabled, it drives low.

Features

• Crystal Oscillator with Spread Spectrum Clock (SSXO)
• No Spread Spectrum (XO) Option
• Wide operating output clock frequency range of 10 to166 MHz
• Programmable spread spectrum with nominal 31.5 kHz modulation frequency
• Center spread: ±0.25% to ±2.0%
• Down spread: –0.5% to –4.0%
• No spread: ± 0.0%
• Integrated phase-locked loop (PLL)
• 85 ps typical cycle-to-cycle jitter with SSCLK = 133 MHz
• For more, see pdf

Functional Description

The CY25701 is a Spread Spectrum Crystal Oscillator (SSXO) IC used to reduce the EMI found in today’s high speed digital electronic systems.

The device uses a Cypress proprietary PLL and Spread Spectrum Clock (SSC) technology to synthesize and modulate the frequency of the embedded input crystal. By frequency modulating the clock, the measured EMI at the fundamental and harmonic frequencies are greatly reduced.

Features

• Integrated phase locked loop (PLL)
• Low jitter, high accuracy outputs
• VCXO with analog adjust
• 3.3 V operation

Benefits

• Highest performance PLL tailored for multimedia applications
• Meets critical timing requirements in complex system designs
• Application compatibility for a wide variety of designs

• Integrated Phase-Locked Loop (PLL)
• Low Jitter, High Accuracy Outputs
• VCXO with Analog Adjust
• 3.3V Operation
• Compatible with MK3727 (–1, –4)
• Application compatibility for a wide variety of Designs
• Enables Design compatibility
• Lower Drive Strength settings (CY241V08A–04)
• For more, see pdf

Features

• Integrated phase-locked loop (PLL)
• Low jitter, high-accuracy outputs
• 3.3V operation
• 25-MHz input frequency
• 66.66-MHz or 33.33-MHz selectable output frequency (orig, -3,-11,-31)
• 33.33-MHz or 25-MHz selectable output frequency (-2,-21)

Benefits

• High-performance PLL tailored for Spread Spectrum application
• Meets critical timing requirements in complex system designs
• Enables application compatibility
• Works with commonly available crystal or driven reference
• Downspread Spread Spectrum with 30-kHz nominal modulation frequency

Features

• Fully Integrated Phase-Locked Loop (PLL)
• FailSafe™ Output
• 8 kHz Reference Clock
• PLL Driven by a Crystal Oscillator that is Phase Aligned with External Reference
• Selectable Standard Communication Output Frequencies
• Low Jitter, High Accuracy Outputs
• 3.3V Operation
• 16-Pin TSSOP Package
• Commercial and Industrial Temperature Ranges

Functional Description

CY26049 is a FailSafe frequency synthesizer with a reference clock input and three clock outputs. The device provides an optimum solution for applications which require continuous operation in case of primary clock failure. The continuous, glitch-free operation is achieved by using a DCXO which serves as a primary clock source.

• 50 to 166 MHz Operating Frequency Range
• Wide Range of Spread Selections: 9
• Accepts Clock and Crystal Inputs
• Low Power Dissipation
  • 70 mW-Typ at 66 MHz
• Frequency Spread Disable Function
• Center Spread Modulation
• Low Cycle-to-cycle Jitter
• 8-pin SOIC Package
   

General Description

CY25561 is a spread spectrum clock generator (SSCG) IC used to reduce electromagnetic Interference (EMI) found in today's high speed digital electronic systems.

CY25561 uses a Cypress proprietary Phase Locked Loop (PLL) and Spread Spectrum Clock (SSC) technology to synthesize and frequency modulate the input frequency of the reference clock. By doing this, the measured EMI at the fundamental and harmonic frequencies of clock (SSCLK) is reduced. 

Features

• Device operating voltage options:
  • MoBL® Clock M3000 family: 1.8 V
  • MoBL Clock M6000 family: 2.5 V, 3.0 V, or 3.3 V
• Selectable clock output voltages for both MoBL clock M3000 and M6000:
  • 1.5 V, 1.8 V, 2.5 V, 3.0 V, or 3.3 V
• Fully integrated ultra-low power phase-locked loops (PLLs)
• Input reference clock frequency range:
  • External crystal: 8 to 48 MHz
  • External reference: 1- to 48-MHz clock
• For more, see pdf
   

General Description

Three Configurable PLLs

The MoBL® Clock M3000/M6000 family of products are three-PLL clock generator ICs designed for cell phone, portable, or consumer electronics applications. It can be used to generate three independent output frequencies ranging from 3 MHz to 50 MHz from a single input reference clock.

Features

• Crystal oscillator with CMOS output
• Output frequency from 8 MHz to 200 MHz
• Two frequency margining control pins (FS0, FS1)
• Output enable or power-down function
• Factory configured or field programmable
• Integrated phase-locked loop (PLL)
• Supply voltage: 3.3 V or 2.5 V
• Pb-free package: 5.0 × 3.2 mm LCC
• Commercial and industrial temperature ranges
   

Functional Description

The CY2XF32 is a high performance and high frequency crystal oscillator (XO). It uses a Cypress proprietary low noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed via two select pins, allowing easy frequency margin testing in applications.

The CY2XF32 is available as a factory configured device or as a field programmable device.

Features

• Low Jitter Crystal Oscillator (XO)
• Less than 1 ps Typical RMS Phase Jitter
• Differential LVPECL Output
• Output Frequency from 50 MHz to 690 MHz
• Two Frequency Margining Control Pins (FS0, FS1)
• Factory Configured or Field Programmable
• Integrated Phase-Locked Loop (PLL)
• Supply Voltage: 3.3V or 2.5V
• Pb-Free Package: 5.0 x 3.2 mm LCC
• Commercial and Industrial Temperature Ranges
   

Functional Description

The CY2XF34 is a high performance and high frequency Crystal Oscillator (XO). It uses a Cypress proprietary low noise PLL to synthesize the frequency from an integrated crystal. The output frequency can be changed through two select pins, allowing easy frequency margin testing in applications.

• One LVPECL Output Pair
• Selectable Frequency Multiplication: x2.5 or x5
• External Crystal Frequency: 25.0 MHz
• Output Frequency: 62.5 MHz or 125 MHz
• Low RMS Phase Jitter at 125 MHz, using 25 MHz Crystal (1.875 MHz to 20 MHz): 0.4 ps (Typical)
• Phase Noise at 125 MHz:
  

  Offset	Noise Power
  1 kHz	–117 dBc/Hz
  10 kHz	–126 dBc/Hz
  100 kHz	–131 dBc/Hz
  1 MHz	–131 dBc/Hz

• Pb-free 8-Pin TSSOP Package
• Supply Voltage: 3.3V or 2.5V
• Commercial and Industrial Temperature Ranges

Functional Description

Features

• Device Operating Voltage Options:
  • MoBL Clock M300 Family: 1.8V
  • MoBL Clock M600 Family: 2.5V, 3.0V, or 3.3V
• Selectable clock output voltages for both MoBL Clock M300 and M600:
  • 1.5V, 1.8V, 2.5V, 3.0V, or 3.3V
• Fully integrated ultra low power phase-locked loops (PLLs)
• Input reference clock frequency range: 1–48 MHz
• Output clock frequency range: 3–50 MHz
• Three I2C™ programmable output clocks
• For more, see pdf
   

General Description

3 Configurable PLLs

The MoBL® Clock M300/M600 Family of products are three-PLL Clock Generator ICs designed for cell phone, portable, or consumer electronics applications. It can be used to generate three independent output frequencies ranging from 3 to 50MHz from a single input reference clock.

Features

• Device Operating Voltage Options:
  • MoBL Clock M4000 Family: 1.8V
  • MoBL Clock M8000 Family: 2.5V, 3.0V, or 3.3V
• Selectable clock output voltages for both MoBL Clock M4000 and M8000:
  • 1.5V, 1.8V, 2.5V, 3.0V, or 3.3V
• Fully integrated ultra low power phase-locked loops (PLLs)
• Input reference clock frequency range:
  • External crystal: 8 to 48 MHz
  • External reference: 1 to 48 MHz clock
• For more, see pdf
   

General Description

4 Configurable PLLs

The MoBL® Clock M4000/M8000 Family of products are four-PLL Clock Generator ICs designed for cell phone, portable, or consumer electronics applications. It can be used to generate four independent output frequencies ranging from 3 to 50MHz from a single input reference clock.

• High-frequency VCXO with LVPECL output
• Any output frequency from 50 MHz to 690 MHz
• Available either factory configured or field programmable
• Integrated phase-locked loop (PLL)
• 1 ps typical RMS Phase Jitter
• Output Enable or Power-down function
• Supply voltage: 3.3 V or 2.5 V
• Pb-free package: 5.0 × 3.2 mm LCC
• Commercial and industrial temperature ranges
• For more, see pdf

Functional Description

The CY2V014 is a high-performance high-frequency voltage-controlled crystal oscillator (VCXO).

The device uses a Cypress proprietary low-noise PLL to synthesize the frequency from an embedded crystal.

The output frequency is user adjustable by means of an analogcontrol voltage applied to the VIN pin.

Features

• One LVPECL Output Pair
• Output Frequency: 312.5 MHz
• External Crystal Frequency: 25 MHz
• Low RMS Phase Jitter at 312.5 MHz, using 25 MHz crystal (1.875 MHz to 20 MHz): 0.3 ps (typical)
• Pb-Free 8-Pin TSSOP Package
• Supply Voltage: 3.3V or 2.5V
• Commercial and Industrial Temperature Ranges

Functional Description

The CY2XP311 is a PLL (Phase Locked Loop) based high performance clock generator. It is optimized to generate 10 Gb Ethernet, SONET, and other high performance clock frequencies. It also produces an output frequency that is 12.5 times the crystal frequency. It uses Cypress’s low noise VCO technology to achieve 0.3 ps typical RMS phase jitter, which meets both 10 Gb Ethernet and SONET jitter requirements. The CY2XP311 has a crystal oscillator interface input and one LVPECL output pair.

Features

• 25 MHz Crystal or Clock Input
• Four Differential 100 MHz PCI-Express Clocks
• Supports HCSL or LVDS Compatible Output Levels
• One Single-ended 25 MHz Output
• Spread Spectrum Capability on all 100 MHz PCI-Express Clock Outputs
• SMBus Interface with Read Back Capability
• 32-pin QFN Package
• Operating Voltage 3.3V
• Commercial and Industrial Operating Temperature Range

Functional Description

CY24292 is a clock generator device intended for PCI-Express applications. The device includes: four 100 MHz differential clocks with HCSL or LVDS compatible outputs for PCI-Express, and one single-ended 25 MHz output.

Features

• Spread Spectrum, VCXO, and Frequency Select
• Input frequency range:
  • Crystal: 8–30 MHz
  • CLKIN: 0.5–100 MHz
• Output frequency:
  • Commercial: 1–200 MHz
  • Industrial: 1–166 MHz
• Integrated phase-locked loop
• Low jitter, high accuracy outputs
• 3.3V operation
• 8-pin SOIC package

The CY22800 is a multi-function clock generator that supports various applications in consumer and communications markets. The device uses the Cypress proprietary PLL along with Spread Spectrum and VCXO technology to make it one of the most versatile clock synthesizers in the marketplace.

Features

• Fully integrated phase-locked loops (PLLs)
• QFN package
• 40% smaller than 20-pin TSSOP
• 22% smaller than 16-pin TSSOP
• Selectable Output Frequency
• Programmable Output Frequencies
• Output Frequency Range of 5-166 MHz
• Input Frequency Range
• Crystal: 10-30 MHz
• For more, see pdf

General Description

The CY22388 family of devices has an Analog VCXO (Voltage Controlled Crystal Oscillator), 4 PLLs, up to 8 clock outputs and frequency selection capabilities. The frequency selects do not modify any PLL frequency. Instead they allow the user to choose between up to 8 different output divider selections depending on the clock and package configuration. This is illustrated in the following Frequency Selection tables and Functional Block Diagram. 

Features

• Maximized EMI suppression using Cypress’s Spread Spectrum technology
• Reduces measured EMI by as much as 10 dB
• Four skew-controlled copies of CPU output
• Four skew-controlled copies of SDRAM output
• One copy of 14.31818-MHz Reference output
• One copy of 48-MHz USB clock (not spread)
• Selectable SSFTG modulation width
• Available in 28-pin SSOP (209 mil)

Spread Spectrum Generator

The device generates a clock that is frequency modulated in order to increase the bandwidth that it occupies. By increasing the bandwidth of the fundamental and its harmonics, the amplitudes of the radiated electromagnetic emissions are reduced.

Features

• Integrated phase-locked loop (PLL)
• Commercial and industrial operation
• Flash programmable
• Field programmable
• Two-wire I2C interface
• Low skew, low jitter, high accuracy outputs
• 3.3 V operation with 2.5 V output option
• 16-pin TSSOP
• For more, see pdf

Frequency Calculation and Register Definitions

The CY22150 is an extremely flexible clock generator with four basic variables that are used to determine the final output frequency. They are the input reference frequency (REF), the internally calculated P and Q dividers, and the post divider, which can be a fixed or calculated value.

 Two Outputs PCI-Express Clock Generator

Features

• 25 MHz Crystal or Clock Input
• Two sets of Differential PCI-Express Clocks
• Pin Selectable Output Frequencies
• Supports HCSL or LVDS Compatible Output Levels
• Spread Spectrum Capability on all Output Clocks with Pin Selectable Spread Range
• 16-pin TSSOP Package
• Operating Voltage 3.3V
• Commercial and Industrial Operating Temperature Range

Functional Description

CY24293 is a two output PCI-Express clock generator device intended for networking applications. The device takes 25 MHz crystal or clock input and provides two pairs of differential outputs at 25 MHz, 100 MHz, 125 MHz, or 200 MHz for HCSL signaling standard.

Features

• Integrated phase-locked loop (PLL)
• Commercial and Industrial operation
• Flash-programmable
• Field-programmable
• Low-skew, low-jitter, high-accuracy outputs
• 3.3 V operation with 2.5 V output option
• 16-pin TSSOP package (CY22050)
• 16-pin TSSOP package with NiPdAu lead finish (CY220501)
• For more, see pdf

Functional Description

The CY22050 is programmable clock generator for use in networking, telecommunication, datacom, and other general-purpose applications. The CY22050 offers up to six configurable outputs in a 16-pin TSSOP, running off a 3.3 V power supply. The on-chip reference oscillator is designed to run off an 8–30-MHz crystal, or a 1–133-MHz external clock signal.

Features

• Three Integrated Phase-locked Loops
• Ultra Wide Divide Counters (8-bit Q, 11-bit P, and 7-bit Post Divide)
• Improved Linear Crystal Load Capacitors
• Flash Programmability
• Field Programmable
• Low-jitter, High-accuracy Outputs
• Power Management Options (Shutdown, OE, Suspend)
• Configurable Crystal Drive Strength
• Frequency Select through three External LVTTL Inputs
• 3.3V Operation
• 16-pin TSSOP Packages
• CyClocksRT™ Support

Operation

The CY22392 is an upgrade to the existing CY2292. The new device has a wider frequency range, greater flexibility, improved performance, and incorporates many features that reduce PLL sensitivity to external system issues.

The device has three PLLs which, when combined with the reference, enable up to four independent frequencies to be output on up to six pins. These three PLLs are completely programmable.

Features

• Supports clock requirements for printers
• 48-MHz spread spectrum clock output
• 48-MHz reference clock output
• Two selectable spread percentages: –1% and –3%
• Integrated loop filter
• 48-MHz crystal or external clock input
• 3.3-V supply operation (2.5-V functional)
• 8-pin small outline integrated circuit (SOIC) package

Functional Description

The CY27020 clock generator provides a low EMI clock output for printers. It features spread spectrum technology, a modulation technique designed specifically for reducing EMI at the fundamental frequency and its harmonics.

Features

• Three integrated phase-locked loops
• Ultra-wide divide counters (eight-bit Q, eleven-bit P, and seven-bit post divide)
• Improved linear crystal load capacitors
• Flash programmability
• Field programmability
• Low-jitter, high-accuracy outputs
• Power-management options (Shutdown, OE, Suspend)
• Configurable crystal drive strength
• Frequency select option through external LVTTL Input
• For more, see pdf

Operation

The CY22381 is an upgrade to the existing CY2081. The new device has a wider frequency range, greater flexibility, improved performance, and incorporates many features that reduce PLL sensitivity to external system issues.

The device has three PLLs that allow each output to operate at an independent frequencies. These three PLLs are completely programmable.

The CY223811 is the CY22381 with NiPdAu lead finish.

Features

• Flash programmable die for in-package programming of crystal oscillators
• High resolution phase-locked loop (PLL) with 10-bit multiplier and 7-bit divider
• Flash programmable capacitor tuning array
• Simple two-pin programming interface (excluding VDD and VSS pins)
• On-chip oscillator used with external 25.1 MHz fundamental tuned crystal
• Flash programmable spread spectrum with spread percentages between ± 0.25% and ± 2.00%
• Spread spectrum on/off function
• Operating frequency: 5 MHz to 170 MHz at 3.3V ± 10%
• Seven-bit linear post divider with divide options from divide-by-2 to divide-by-127
• For more, see pdf

Functional Description

CY5057 is a Flash programmable, high accuracy, PLL-based die designed for the crystal oscillator market. It also contains spread spectrum circuitry that is enabled or disabled with an external pin. The die is integrated with a low cost 25.1 MHz fundamental tuned crystal in a 4 or 6-pin through hole or surface mount package. The oscillator devices may be stocked as blank parts and custom frequencies programmed in-package at the last stage before shipping. This enables faster manufacturing of custom and standard crystal oscillators without the need for dedicated and expensive crystals.

Features

• Meets Rambus(R) Extended Data Rate (XDR(TM)) clocking requirements
• 25 ps typical cycle-to-cycle jitter
  • -135 dBc/Hz typical phase noise at 20 MHz offset
• 100 or 133 MHz differential clock input
• 300-667 MHz high speed clock support
• Quad (open drain) differential output drivers
• Supports frequency multipliers: 3, 4, 5, 6, 9/2 and 15/4
• Spread Aware(TM)
• 2.5V operation
• 28-pin TSSOP package

Features

• Four fully integrated phase locked loops (PLLs)
• Input frequency range
  • External crystal: 8 to 48 MHz
  • External reference: 8 to 166 MHz clock
• Wide operating output frequency range
  • 3 to 166 MHz
• Serial programmable over 2-wire I2C interface
• Programmable spread spectrum with center and down spread option and Lexmark and Linear modulation profiles
• VDD supply voltage options:
  • 2.5V, 3.0V, and 3.3V for CY2545
• For more, see pdf

General Description

Four Configurable PLLs

The CY2545 and CY2547 have four I2C programmable PLLs available to generate output frequencies ranging from 3 to 166 MHz. The advantage of having four PLLs is that a single device generates up to four independent frequencies from a single crystal. Two sets of frequencies for each PLL can be programmed. This enables in system frequency switching using multifunction frequency select pin, FS.

Features

• 4 to 32 MHz Input Frequency Range
• 4 to 128 MHz Output Frequency Range
• Accepts Clock, Crystal, and Resonator Inputs
• 1x, 2x, and 4x frequency multiplication:
  • CY25811: 1x; CY25812: 2x; CY25814: 4x
• Center and Down Spread Modulation
• Low Power Dissipation:
  • 3.3V = 52 mW - typ at 6 MHz
  • 3.3V = 60 mW - typ at 12 MHz
• For more, see pdf

Functional Description

The CY25811/12/14 products are Spread Spectrum Clock Generator (SSCG) ICs used for the purpose of reducing electromagnetic interference (EMI) found in today’s high speed digital electronic systems.

The devices use a Cypress proprietary phase-locked loop (PLL) and Spread Spectrum Clock (SSC) technology to synthesize and modulate the frequency of the input clock. By frequency modulating the clock, the measured EMI at the fundamental and harmonic frequencies is greatly reduced.

Features

• 8- to 32-MHz input frequency range
• CY25819: 16 MHz to 32 MHz
• Separate modulated and unmodulated clocks
• Accepts clock, crystal, and resonator inputs
• Down spread modulation
• Power-down function
• Low-power dissipation
  • CY25819 = 36 mW typ at 16 MHz
  • CY25819 = 63 mW typ at 32 MHz
• Low cycle-to-cycle jitter
  • SSCLK = 250 ps typ
  • REFOUT = 275 ps typ
• Available in 8-pin (150 mil) SOIC package

Overview

The Cypress CY25819 products are Spread Spectrum Clock Generator (SSCG) ICs used for the purpose of reducing EMI found in today’s high-speed digital electronic systems. The devices use a Cypress proprietary phase-locked loop (PLL) and Spread Spectrum Clock (SSC) technology to synthesize and modulate the frequency of the input clock.

• 4 to 32 MHz Input Frequency Range
• 4 to 128 MHz Output Frequency Range
• Accepts Clock, Crystal and Resonator Inputs
• 1x, 2x and 4x Frequency Multiplication
• Non-modulated Reference Frequency Output
• Center and Down Spread Modulation
• Low Power Dissipation
  • 3.3V = 52 mW-typ at 6 MHz
  • 3.3V = 60 mW-typ at 12 MHz
• For more, see pdf

General Description

The Cypress CY25568 is a Spread Spectrum Clock Generator (SSCG) IC used for the purpose of reducing Electro Magnetic  Interference (EMI) found in today's high-speed digital electronic systems.      More...

Features

• Erasable programmable read only memory (EPROM) - programmable die for in-package programming of crystal oscillators
• High resolution Phase locked loop (PLL) with 12-bit multiplier and 10-bit divider
• EPROM programmable capacitor tuning array with optional shadow register
• Twice programmable die
• Simple 2-wire programming interface
• On-chip oscillator runs from 10 MHz to 30 MHz fundamental tuned crystal
• EPROM-selectable Transistor transistor logic (TTL) or Complementary metal oxide semiconductor (CMOS) duty cycle levels
• Operating frequency:
  • 1 MHz to 133 MHz at 5 V
• For more, see pdf

Functional Description

CY2037 is an EPROM-programmable, high accuracy, PLL-based die designed for the crystal oscillator market. The die attaches directly to a low cost 10 to 30 MHz crystal and can be packaged into a 4-pin through-hole or surface mount packages. The oscillator devices may be stocked as blank parts and custom frequencies programmed in-package at the last stage before shipping. This enables fast-turn manufacture of custom and standard crystal oscillators without the need for dedicated, expensive crystals.

• One low-voltage differential signaling (LVDS) Output Pair
• Output Frequency: 100 MHz
• External Crystal Frequency: 25 MHz
• Low RMS Phase Jitter at 100 MHz, using 25 MHz Crystal (637 kHz to 10 MHz): 0.53 ps (Typical)
• Pb-free 8-Pin TSSOP Package
• Supply Voltage: 3.3V or 2.5V
• Commercial Temperature Range

Features

• Four fully integrated phase locked loops (PLLs)
• Input frequency range
  • External crystal: 8 to 48 MHz
  • External reference: 8 to 166 MHz clock
• Wide operating output frequency range
  • 3 to 166 MHz
• Programmable Spread Spectrum with Center and Down Spread option and Lexmark and Linear modulation profiles
• Selectable VDD supply voltage options:
  • 2.5V, 3.0V, and 3.3V
• For more, see pdf
   

General Description

Four Configurable PLLs

The CY25404 has four programmable PLLs that can be used to generate output frequencies ranging from 3 to 166 MHz. The advantage of having four PLLs is that a single device generates up to four independent frequencies from a single crystal.

Features

• Four fully integrated phase locked loops (PLLs)
• Input frequency range
  • External crystal: 8 to 48 MHz for CY2544 and CY2546
  • External reference: 8 to 166 MHz clock
• Reference clock input voltage range
  • 2.5V, 3.0V, and 3.3V for CY2548
  • 1.8V for CY2544 and CY2546
• Wide operating output frequency range
  • 3 to 166 MHz
• For more, see pdf

General Description

Four Configurable PLLs

The CY2544, CY2548 and CY2546 have four programmable PLLs that can be used to generate output frequencies ranging from 3 to 166 MHz. The advantage of having four PLLs is that a single device generates up to four independent frequencies from a single crystal.

Features

• 3.3V operation
• 96- and 100-MHz frequency support
• Selectable slew rate control
• 200-ps jitter
• I2C programmability
• 250-µA power-down current
• Lexmark Spread Spectrum for best electromagnetic interference (EMI) reduction
• 16-pin TSSOP package

Features

• Wide Operating Output (SSCLK) Frequency Range
  • 3 MHz to 200 MHz
• Programmable Spread Spectrum with nominal 31.5 kHz Modulation Frequency
  • Center Spread: ±0.25% to ±2.5%
  • Down Spread: –0.5% to –5.0%
• Input frequency range
  • External Crystal: 8 to 30 MHz Fundamental Crystals
  • External Reference: 8 to 166 MHz Clock
• Integrated Phase-Locked Loop (PLL)
• For more, see pdf

General Description

The CY25100 is a Spread Spectrum Clock Generator (SSCG) IC used to reduce EMI found in today’s high speed digital electronic systems.

The device uses a Cypress proprietary PLL and Spread Spectrum Clock (SSC) technology to synthesize and modulate the frequency of the input clock. By frequency modulating the clock, the measured EMI at the fundamental and harmonic frequencies are greatly reduced.

Features

• Three fully integrated phase locked loops (PLLs)
• Input frequency range
  • External crystal: 8 to 48 MHz
  • External reference: 8 to 166 MHz clock
• Reference Clock input voltage range
  • 2.5 V, 3.0 V, and 3.3 V for CY25483
  • 1.8 V for CY25403 and CY25423
• Wide operating output frequency range
  • 3 to 166 MHz
• For more, see pdf

General Description

3 Configurable PLLs

The CY25403, CY25423, and CY25483 have three programmable PLLs that can be used to generate output frequencies ranging from 3 to 166 MHz. The advantage of having three PLLs is that a single device generates up to three independent frequencies from a single crystal.

Features

• Two fully integrated phase locked loops (PLLs)
• Input frequency range
  • External crystal: 8 to 48 MHz
  • External reference: 8 to 166 MHz clock
• Reference Clock input voltage range
  • 2.5 V, 3.0 V, and 3.3 V for CY25482
  • 1.8 V for CY25402 and CY25422
• Wide operating output frequency range
  • 3 to 166 MHz
• For more, see pdf

General Description

2 Configurable PLLs

The CY25402, CY25422, and CY25482 have two programmable PLLs that can be used to generate output frequencies ranging from 3 to 166 MHz. The advantage of having two PLLs is that a single device generates two independent frequencies from a single crystal.

Features

• Three integrated phase-locked loops (PLLs)
• Ultra wide divide counters (8-bit Q, 11-bit P, and 7-bit post divide)
• Improved linear crystal load capacitors
• Flash programmability with external programmer
• Field-programmable
• Low jitter, high accuracy outputs
• Power management options (Shutdown, OE, Suspend)
• Configurable crystal drive strength
• Frequency select through three external LVTTL inputs
• 3.3-V operation
• 16-pin TSSOP package
• CyClocksRT™ software support

Functional Description

The CY22393, CY22394, and CY22395 are a family of parts designed as upgrades to the existing CY22392 device. These parts have similar performance to the CY22392, but provide advanced features to meet the needs of more demanding applications.

The clock family has three PLLs which, when combined with the reference, allow up to four independent frequencies to be output on up to six pins. These three PLLs are completely programmable.

Part numbers beginning with CY2XF23FLX are field programmable devices.  They are unprogrammed when shipped.  The user may program them once, using a programmer such as the CY3675 CyClockMaker.

Part numbers beginning with CY2XF23LX are factory programmed devices.  They are programmed by Cypress prior to shipping, and cannot be reprogrammed afterwards.

As these devices have SDAT and SCLK pins for I2C programming, you have an option to re-program only the volatile memory registers of the factory programmed devices In-system. This means that when you Power-On the device, it will run with the Power On factory programmed configuration which is present in the non-volatile memory registers. Later, you can change the configuration by making changes to the volatile memory registers using I2C. Now, this change will last as long as the device is powered. The new configuration will be lost once the device is powered down and the next time when it is Powered-ON, it will have the factory programmed configuration.

• 50 to 200 MHz operating frequency range
• Wide range of spread selections: 9
• Accepts clock and crystal Inputs
• Low power dissipation
  • 70 mW Typ (Fin = 65 MHz)
• Frequency spread disable function
• Center spread modulation
• Low cycle-to-cycle jitter
• 8-pin SOIC package
   

General Description

CY25562 is a spread spectrum clock generator (SSCG) IC used to reduce electromagnetic interference (EMI) found in today's high speed digital electronic systems.

CY25562 uses a Cypress proprietary phase locked loop (PLL) and spread spectrum clock (SSC) technology to synthesize and frequency modulate the input frequency of the reference clock. By doing this, the measured EMI at the fundamental and harmonic frequencies of clock (SSCLK) is reduced.      More...

Features

• High-accuracy PLL with 12-bit multiplier and 10-bit divider
• EPROM programmability
• 3.3V or 5V operation
• Operating frequency
  • 390 kHz–133 MHz at 5V
  • 390 kHz–100 MHz at 3.3V
• Reference input from either a 10–30 MHz fundamental toned crystal or a 1–75 MHz external clock
• EPROM selectable TTL or CMOS duty cycle levels
• Sixteen selectable post-divide options, using either PLL or reference oscillator/external clock
• For more, see pdf
   

Functional Description

CY2077 is an EPROM-programmable, high-accuracy, general-purpose, PLL-based design for use in applications such as modems, disk drives, CD-ROM drives, video CD players, DVD players, games, set-top boxes, and data/telecommunications.

Features

• Single phase locked loop (PLL) architecture
• EPROM programmability
• Factory programmable (CY2907) or field programmable (CY2907F) device options
• Up to two configurable outputs
• Low skew, low jitter, high accuracy outputs
• Power management (power down, OE)
• Frequency select option
• Configurable 5 V or 3.3 V Operation
• 8-pin or 14-pin SOIC packages

Functional Description

The CY2907 is a general purpose clock generator designed for use in a wide variety of applications—from graphics to PC peripherals to disk drives. It generates selectable system clock frequencies from a single reference input (crystal or reference clock). The CY2907 is configured with an EPROM array, similar to the other devices in the Cypress EPROM Programmable Clock family, making it easy to customize for any application. Furthermore, the CY2907 is compatible with all industry standard 9107 and 9108 clock synthesizers.

Hardware -- The CY3670 programmer or programmers from qualified vendors such as BP Microsystems.
Software -- CyberClocks, included with the programmer.

Designers can download CyberClocks from the Cypress website. CyClocksRT, contained within CyberClocks, will generate a JEDEC file which contains all the configuration information. The JEDEC file can then be loaded into the hardware programmer.
 

A data sheet on the CY3670 is available from our website.

CyberClocks software is easily downloaded from our website.

CY22392 - Commercial - 8KHz - 200MHz
CY22392 - Industrial - 8KHz - 166MHz

Note: 8KHz can only be obtained from the buffered 1MHz reference divided by 127 (Maximum output divider value).

PLL Frequency Range:

CY22392 - Commercial - 100MHz - 400MHz

CY22392 - Industrial - 125MHz - 375MHz

The frequency ranges are reduced at higher temperatures for guaranteed PLL stability. The PLLs do not reliably lock at higher temperatures for which reduce the margins.

CY22393 - Commercial - 8KHz - 200MHz
CY22393 - Industrial - 8KHz - 166MHz

Note: 8KHz can only be obtained from the buffered 1MHz reference divided by 127 (Maximum output divider value).

PLL Frequency Range:

CY22393 - Commercial - 100MHz - 400MHz

CY22393 - Industrial - 125MHz - 375MHz

The frequency ranges are reduced at higher temperatures for guaranteed PLL stability. The PLLs do not reliably lock at higher temperatures for which reduce the margins.

• CY2544
• CY2545
• CY2548

NOTE: This kit alone cannot program a clock device. You must also purchase a socket adapter that supports your clock device (see table below for available socket adapters).

Clock programming kits
 

Hardware Description:

The CY3675-CLKMAKER1 Clock Programmer Kit contains:

• CD with:
  • CY3675-CLKMAKER1 Clock Programming Kit Guide
  • Software installation file: PSoC Programmer
• Main programming board (CY3675-CLKMAKER1)
• I2C-USB Bridge (CY3240-I2USB)
• PSoC® MiniProg (CY3217)
• USB cable
• 15V 400mA power supply
• Four power plug adapters

To download the Clock Programmer Software click here.
(Note: Clock Programmer 1.2 is bundled with PSoC Programmer.)

• CY22M1
• CY22U1

NOTE: This kit alone cannot program a clock device. You must also purchase a socket adapter that supports your clock device (see table below for available socket adapters).

Clock programming kits
 

Hardware Description:

The CY3675-CLKMAKER1 Clock Programmer Kit contains:

• CD with:
  • CY3675-CLKMAKER1 Clock Programming Kit Guide
  • Software installation file: PSoC Programmer
• Main programming board (CY3675-CLKMAKER1)
• I2C-USB Bridge (CY3240-I2USB)
• PSoC® MiniProg (CY3217)
• USB cable
• 15V 400mA power supply
• Four power plug adapters

To download the Clock Programmer Software click here.
(Note: Clock Programmer 1.2 is bundled with PSoC Programmer.)

• CY25404

NOTE: This kit alone cannot program a clock device. You must also purchase a socket adapter that supports your clock device (see table below for available socket adapters).

Clock programming kits
 

Hardware Description:

The CY3675-CLKMAKER1 Clock Programmer Kit contains:

• CD with:
  • CY3675-CLKMAKER1 Clock Programming Kit Guide
  • Software installation file: PSoC Programmer
• Main programming board (CY3675-CLKMAKER1)
• I2C-USB Bridge (CY3240-I2USB)
• PSoC® MiniProg (CY3217)
• USB cable
• 15V 400mA power supply
• Four power plug adapters

To download the Clock Programmer Software click here.
(Note: Clock Programmer 1.2 is bundled with PSoC Programmer.)

• CY25701
• CY25702

Overview:
The CY3724 socket adapter plugs into the CY3672 programmer, and is used to program the following: CY25701FL and CY25702FL.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.

The CY3670 frequency timing generator (FTG) programming kit provides users (who have a PC) with the ability to program Cypress EPROM field-programmable clock generators quickly and easily.  The two set-up requirements are a power connection and a serial port connection with the PC.

Using CyClocks(TM) software, users configure the generators to given specifications and generate the corresponding JEDEC file.  In addition, CyClocks software has PPM optimization and power calculations.

Hardware Description

The CY3670 FTG programming kit contains a programmer unit, serial port cable, AC/DC adapter, CyClock software, programmer software, and data sheet. The CY3095 and CY3096 socket adapters for CY2292F and CY2071AF devices and other additional socket adapters need to be purchased separately.

For the latest CyberClock software, click here.

NOTE: This kit alone cannot program a clock device. You must also purchase a socket adapter that supports your clock device (see table below for available socket adapters).

Clock programming kits
 

Hardware Description:

The CY3675-CLKMAKER1 Clock Programmer Kit contains:

• CD with:
  • CY3675-CLKMAKER1 Clock Programming Kit Guide
  • Software installation file: PSoC Programmer
• Main programming board (CY3675-CLKMAKER1)
• I2C-USB Bridge (CY3240-I2USB)
• PSoC® MiniProg (CY3217)
• USB cable
• 15V 400mA power supply
• Four power plug adapters

To download the Clock Programmer Software click here.
(Note: Clock Programmer 1.2 is bundled with PSoC Programmer.)

Overview:
The CY3698 socket adapter plugs into the CY3672 programmer, and is used to program the following: CY22392F, CY22393F, CY22394F and CY22395F.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.

Overview:
The CY3697 socket adapter plugs into the CY3672 programmer, and is used to program the CY2077 in the TSSOP package: CY2077FZ.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.

Overview:
The CY3696 socket adapter plugs into the CY3672 programmer, and is used to program the CY2077 in the SOIC package: CY2077FS.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.

Overview:
The CY3695 socket adapter plugs into the CY3672 programmer, and is used to program the following: CY22050KF, CY22150KF and CY25200KF.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.

Overview:
The CY3699 socket adapter plugs into the CY3672 programmer, and is used to program the CY22381F.

The CY3672 programming kit enables any user with a PC to quickly and easily program Field-programmable Clock Gener­ators. The only set-up requirements are a power connection and USB port (CY3672-USB) connection with the PC.

Using CyClocksRT(TM) (embedded in CyberClocks software) or CyberClocks Online, users can configure their parts to a given specification and generate the corresponding JEDEC file. In addition, CyClocksRT software provides PPM optimization and power calculations.

The JEDEC file is then loaded into CY3672 software that communicates with the programmer. The CY3672 software has the ability to read and view the EPROM table from a programmed device.

Hardware Description

The following socket adapters support the associated programming device.