|
Title
|
Customer Rating
|
Updated
|
Footprint / Landpattern of an SRAM?
Where can i get recommended footprint / Landpattern for standard packages?
|
Not yet rated
|
09/12/12 |
Maximum Junction Temperature and Power Consumption Calculator
How can I find the power consumption, maximum junction temperature and absolute maximum temperature of an SRAM part ?
|
(4/5) by 1
user
|
05/07/12 |
Why do your address pins not match Samsungs or other vendors?
Parts by other vendors are obsolete. In the Cypress equivalent part the address and data lines are different. Can i use Cypress part without changes in firmware?
|
Not yet rated
|
04/16/12 |
ISB2 vs Temp and ISB2 vs VCC for CY62147EV30
Provide the characterization data for ISB2 vs Temp and ISB2 vs VCC
|
Not yet rated
|
03/13/12 |
MoBL SRAM Definition
What are MoBL SRAMs?
|
Not yet rated
|
03/13/12 |
Vss and Vcc clarification
Which pin is ground: Vcc or Vss?
|
Not yet rated
|
03/13/12 |
Battery back up for SRAM's
Does Cypress recommend any lithium battery backup for SRAM's?
|
Not yet rated
|
03/13/12 |
Floating data input on CMOS SRAM
I used a SRAM which has a x32 configuration and now I am forced to use a x36 configuration. I have the 4 unused inputs floating. Is this okay?
|
Not yet rated
|
03/13/12 |
Do Address pins have internal Pull-up or Pull-down circuits?
Do you have internal pullups or pulldowns on your address pins so that they may be left floating?
|
Not yet rated
|
03/13/12 |
Do you have Land Patterns or layouts
Do you have a recommended land pattern for my Cypress device?
|
Not yet rated
|
03/13/12 |
Does
What does the 'T' at the end of some part numbers mean?
|
Not yet rated
|
03/13/12 |
DRAM Availability
Does Cypress make DRAM?
|
Not yet rated
|
03/13/12 |
How to Submit Parts for FA
How can I send a device in for failure analysis?
|
Not yet rated
|
03/13/12 |
Erase contents of SRAM
What is the voltage at which we can ensure the contents of SRAM are completely erased?
|
Not yet rated
|
01/04/12 |
Difference in Maximum and Typical Standby Currents
Why is there a huge difference between the maximum standby current and the typical standby current.
|
Not yet rated
|
12/29/11 |
Can the CY62147VLL-70ZI replace the CY62146VLL-70ZI without any hardware/software changes?
Question: Can CY62147VLL-70ZI be replaced by CY62146VLL-70ZI without any software/hardware changes?
|
Not yet rated
|
12/28/11 |
Part Number Decoder for Ultra Low Power SRAMs
Question: Is a part number decoder for the Ultra Low Power SRAM family available?
|
Not yet rated
|
12/28/11 |
Determining the Absolute Maximum Junction Temperature
How to determine the absolute maximum Junction temperature for a given Memory part?
|
Not yet rated
|
12/28/11 |
Battery backup for Micropower SRAM
What are the possible options to design a battery backed up memory interface on a board?
|
Not yet rated
|
11/18/11 |
Moisture Sensitivity Level (MSL) of Cypress Parts
How do I find Moisture Sensitivity Level (MSL) of Cypress parts?
|
Not yet rated
|
09/08/11 |
Constraints and Interchangeability of Data and Address pins in Async SRAMs
Can I interchange the address pins in Cypress Async SRAMs ? Or Can I interchange the data pins in Cypress Async SRAMs ?
|
Not yet rated
|
09/01/11 |
Byte Power Down feature in MoBL SRAMs
How does the Byte Power Down feature work in Cypress MoBL SRAMs ?
or If I de-assert both BHE# & BLE#, will my device get deselected ?
or Which devices have Byte Power Down feature available ?
|
Not yet rated
|
09/01/11 |
clarify tSCE
In MPWR SRAMs, when device wakes up from standby, is the time to write solely determined by tSCE?
|
(5/5) by 1
user
|
09/01/11 |
Interleaved part
Is the P/N CY7C1041DV33 an interleaved part? Are the Logical bits physically adjacent in a RAM array?
|
Not yet rated
|
09/01/11 |
Load Capacitance of Tri-State Data bus of many SRAMs connected together
What will be the load capacitance of a Tri-State Data bus when more than one SRAM busses are connected together?
|
Not yet rated
|
09/01/11 |
Does CY62256 have pull up resistor on the I/O ?
Does this part have pull up resistors on the I/O pins?
|
Not yet rated
|
06/26/11 |
Overshoot and Undershoot spec in datasheet
What are the overshoot and undershoot specs of Async SRAM's
|
Not yet rated
|
06/26/11 |
Async SRAM's support BSDM format models (Boundary Scan Description Model)?
Does Async SRAM's support BSDM format models (Boundary Scan Description Model)?
|
Not yet rated
|
06/26/11 |
Decoupling for the CY7C1041CV33-12BAI ?
What decoupling scheme should I use for Async SRAM's?
|
(1/5) by 1
user
|
06/26/11 |
Data retention mode for the CY7C1049CV33 ?
What is the difference between stand-by mode and data retention mode for the CY7C1049CV33?
|
Not yet rated
|
06/26/11 |
cross-section drawings and thickness ?
Where do I Request a cross-section drawing with layers labeled and nominal thickness that can be identified?
|
Not yet rated
|
06/26/11 |
DIFFERENCE BETWEEN THE CY62128LL-70SC AND CY62128BLL-70SC ?
What is the difference between the CY62128LL-70SC AND CY62128BLL-70SC ?
|
Not yet rated
|
06/20/11 |
SRAM Environmental Testing
Where is the environmental and mechanical testing data available.
|
Not yet rated
|
06/20/11 |
Unused OE# and CE1 Pins
If I am not going to use these pins, what should I do with them?
|
Not yet rated
|
06/11/11 |
Difference in version Standard, L and LL
What are the differences between the Standard, L version and LL version?
|
Not yet rated
|
06/09/11 |
Differences between the CY62126/36/46 and the CY62127/37/47
What is the difference between the CY62126 /CY62136 / CY62146 and the CY62127 / CY62137 /CY62147?
|
Not yet rated
|
04/04/11 |
Difference Between MoBL and MoBL2
What is the difference between MoBL and MoBL2?
|
Not yet rated
|
04/04/11 |
SRAM powerup data output
If a read occurs on power up of an SRAM device, does the memory deliver highs, lows or high-z, since no data was ever loaded into the memory.
|
Not yet rated
|
04/04/11 |
tLZOE and tHZOE demystified
Timing specification on some datasheets mentions timings tLZOE(min) and tHZOE(max) as 5 and 20 ns respectively. But foot note 15 mentions at any given temp and voltage tHZOE is less then tLZOE. Please clarify the interpretation of this?
|
Not yet rated
|
04/04/11 |
UL94V-0_compliance
Are all of your devices UL94V-0 compliant?
|
Not yet rated
|
04/04/11 |
Extra 4 or 2 bits if 32/16 bits are used in x36/x18 part.
what do I do with the extra 4 or 2 bits if I want to use only 32/16 bits in a X36/X18 part?
|
Not yet rated
|
04/04/11 |
Ram 4 and Ram 5 on your Reliability report
What does Ram 4 and Ram 5 on your Reliability report mean?
|
Not yet rated
|
04/04/11 |
extra 2 bits for parity check?
Why do we have 2 extra bits for parity checking.
|
Not yet rated
|
04/04/11 |
Mean time between failures?
How to calculate mean time between failures (MTBF)?
|
Not yet rated
|
04/04/11 |
Parity during read and write
How is parity generated during reads and write?
|
Not yet rated
|
04/04/11 |
Failure In Time (FIT)
Where do I find the FIT value for a particular device?
|
Not yet rated
|
04/04/11 |
status of pins while using CY62157EV as 1Mx8 or 512Kx16
What should be the state of the pins while using CY62157EV30LL as 1Mx8 or 512Kx16
|
Not yet rated
|
04/04/11 |
Qualification Report (QTP)
How do I find a Qualification Report for a particular device?
|
Not yet rated
|
04/04/11 |
Initial data at power-up for the SRAMs
If you power up the SRAM's, and do not write to any of the locations, is there an inherent predisposition for the registers to settle at either 00,FF, etc.?
|
Not yet rated
|
03/30/11 |
Use of second chip enable on the SRAM parts ?
Does the second chip enable on the SRAM pars provide any additional functionality?
|
Not yet rated
|
03/30/11 |