Cypress Perform

Home > Support & Community
support.cypress.com     Bookmark and Share
Support & Community

Knowledge Base Search



Selected Type:  Known Problems and Solutions

Keyword: Product: Application:  
Results 1 - 25 of 72 2   3   Next >
Title Customer Rating Updated
How to Avoid the Need for an External EEPROM - KBA83524
Question: Can I use the default VID/PID and default descriptors for the hub to avoid the need for an external EEPROM?

Not yet rated
05/02/13
Difference between FX2LP™ Port I/O, GPIF, and Slave FIFO Modes - KBA83522
Question: What are the key differences between the three modes: Port I/O, GPIF, and FIFO? After I select a mode, can I switch to another?

Not yet rated
05/02/13
Read and Write to EZ-USB® Internal Memory (AN21xx/FX/FX1/FX2/FX2LP™) - KBA87109
Question: Is there a way to read and write to an EZ-USB memory (AN21xx/FX/FX1/FX2/FX2LP) device?

Not yet rated
05/02/13
32-bit GPIF Interface failing at 100 MHz - KBA84082
Question: Why does the 32-bit GPIF interface fail at 100 MHz?

Not yet rated
04/29/13
Detecting Bleed Resistor or Modulating Capacitor Damage - KBA85698
Question: Is there a way to detect if Rb or Cmod are damaged?

Not yet rated
04/12/13
Erratic or Noisy RESET# Signal to FX2LP™ - KBA85498
Question: When I reset an FX2LP using the external RESET# pin with an erratic signal, the chip fails to reset as expected. It also fails subsequent external resets with a proper reset signal. The correct functionality resumes when the whole device is power cycled again. What causes this behavior and how can I avoid it in a design?

Not yet rated
04/08/13
NX2LP™ NAND Programming Utility Does Not Detect NAND Flash on Windows 7 - KBA85453
Question: Why does NX2LP NAND programming utility not detect the NAND Flash on Windows 7?

Not yet rated
03/22/13
USB Driver for WinCE OS for PSoC® 3 or any other USB Peripheral chip - KBA85516
Question: Are there any general-purpose drivers, such as CyUSB.sys, available for WinCE OS?

Not yet rated
03/19/13
"Install driver for Cypress AT2LP RC42” and “Install driver for Cypress AT2LP RC58" Error Messages - KBA84340
Question: How can I recover the data stored on my hard drive when I get an error message saying "Install driver for Cypress AT2LP RC42" or " Install driver for Cypress AT2LP RC58"?

(4.8/5) by 20 users
02/28/13
Missing Watchdog Enable Parameter in CY8C29xxx Devices - KBA85221
Question: I created a new project with one of the CY8C29xxx family devices in PSoC Designer™ 5.3. However, I cannot find the Watchdog Enable parameter in the Global Resources Window. Is there a workaround for this?

Not yet rated
01/08/13
Input Jitter Requirements for 65 nm QDRII/II+/DDRII/II+ Device Family - KBA84380
Question:What are the input jitter requirements for 65 nm QDRII/II+/DDRII/II+ device family?

Not yet rated
11/20/12
How to Resolve QDR-DDR II/II+/Xtreme Verilog Model Simulation Error Using Synopsys VCS - KBA84385
Question:Why Synopsys VCS gives incorrect simulation result with QDR-DDR II/II+/Xtreme verilog models?

Not yet rated
11/20/12
To Detect When a Self-Powered USB Device is Plugged - KBA82850
Question: How do I detect when a self-powered USB device is plugged in?

Not yet rated
10/11/12
New clock synchronization check exposes aliased scan rate issue in CapSense
Why does PSoC Creator 2.1 generate a clock synchronization warning in my working CapSense design?

Not yet rated
06/28/12
SPI with 32 bit GPIF in FX3
Can SPI be used with GPIF II 32 bit in FX3?

Not yet rated
04/26/12
ADC gives incorrect value when CapSense is enabled
When input to an ADC is taken from a MUX bus and if CapSense is enabled, the ADC produces incorrect results? What is the reason for this error and how can this be corrected?

Not yet rated
03/13/12
Using ADC10 with external oscillator gives 0xFFFF as output
Why does ADC10 give 0xFFFF as output when used with external oscillator for any input?

Not yet rated
03/05/12
CY8C20xx7 family CapSense Controller does not provide on-chip debug (OCD) support
Does CY8C20xx7 family CapSense Controller provide on-chip debug (OCD) support?

Not yet rated
02/02/12
First BULK IN packet from BootLdrUSBFS/BootLdrUSBFSe modules always NAK'ed by PC (PSoC Designer 5.2 and before versions)
After entering the Bootloader mode while using BootLdrUSBFS/BootLdrUSBFSe user modules, the first BULK IN packet is always NAK'ed. Why?

Not yet rated
01/29/12
known issues using FX3 with the ASMedia xHCI host controller
Are there any known issues in using FX3 with the ASMedia xHCI host controller?

Not yet rated
01/25/12
Software Reset
Is it possible to make software reset?

Not yet rated
01/01/12
CYFISNP user module disappears in PSD 5.0 SP6
When I open a project with CYFISNP user module with PSoC Designer 5.0 SP6, the CYFISNP user module does not appear in the project. What is the reason and what is the work around?

(5/5) by 2 users
12/30/11
Building PSoC Creator bootloadable project in separate workspaces
Is it possible to build PSoC Creator bootloadable project in separate workspaces?

Not yet rated
12/29/11
PSoC Creator build fails after changing project type from 'Boot Loader' to 'Normal' or from 'Normal' to 'Boot Loader'.
How to change project type from 'Boot Loader' to 'Normal' or from 'Normal' to 'Boot Loader'?

Not yet rated
12/29/11
System DWR Tab in PSoC Creator shows stale "IO Components" in the Bootloader section
Why system DWR tab still showing stale "IO Components" in the Bootloader section?

Not yet rated
12/29/11
Results 1 - 25 of 72 2   3   Next >
Sunset Owner: RAIK; Secondary Owner: GRAA;