Cypress Perform

Home > Support & Community
support.cypress.com     Bookmark and Share
Support & Community

Knowledge Base Search



Selected Type:  Digital

Keyword: Product: Application:  
Results 1 - 25 of 36 1  2   Next >
Title Customer Rating Updated
Creating First Order IIR Lag Filters in the PSoC® 3 and PSoC 5 Filter Component - KBA85693
Question: How can I implement first order IIR lag filters in the PSoC® 3 and PSoC 5 Filter component?
Not yet rated 		03/21/13
Pseudo Random Sequence Generator with PSoC® 1 - KBA83078
Question: How do I generate a random number sequence using PSoC® 1?
Not yet rated 		03/19/13
Using a PRS Generator as a PWM - KBA83077
Question: How do I use a Pseudo Random Sequence (PRS) generator as a Pulse Width Modulator (PWM) in PSoC® Designer?
Not yet rated 		03/19/13
One Shot PWM in PSoC® 3 and PSoC 5 - KBA85546
Question: How do I create a one shot pulse width modulator (PWM) in PSoC® 3 or PSoC 5?
Not yet rated 		03/15/13
Alternate pin for SPI slave clock pin in CY8C20xx6
How to use the the alternate pin for SPI slave clock pin in CY8C20xx6
Not yet rated 		06/13/12
Using DMA to transfer data to SPIM of PSoC 3/5 on TX_FIFO_NOT_FULL flag
SPI Master + DMA (rising edge trigger) configured to work on TX_FIFO_NOT_FULL flag is transmitting only the first data. Why?
Not yet rated 		02/17/12
Difference between count & clock pins of PSoC 3/5 Counter component
What is the difference between count & clock pins of PSoC 3/5 Counter component?
Not yet rated 		02/17/12
Implementation of Virtual COM port / USBUART
Can I implement a Virtual COM port/USBUART functionality in PSoC1?
Not yet rated 		02/09/12
Using UART in PSoC1
How to implement a UART in PSoC1?
Not yet rated 		01/25/12
Erase contents of SRAM
What is the voltage at which we can ensure the contents of SRAM are completely erased?
Not yet rated 		01/04/12
USBUART is not detected when connected to the PC
I use Hyperterminal to connect to an USBUART project. Sometimes, when I plug the USBUART project to the PC, it is not detected by Hyperterminal. When I disconnect and reconnect, it gets detected. What could be the problem?
Not yet rated 		12/29/11
SSDM_Polarity in System Level project
How to invert the "SSDM_Polarity" in System Level project of PSoC Designer 5.0?
Not yet rated 		12/05/11
Sending more bits of data than configured using SPIM Component in PSoC Creator
Can I transfer 16 bit data when the SPI master is configured for 8 data bits in PSoC Creator?
Not yet rated 		06/25/11
1-Wire Communication - Pull Up Resistor
Is an external pull up resistor required in 1-wire communication?
Not yet rated 		06/13/11
Drive strength differences between GPIO and SIO pins in PSoC 3/5
What are the differences in drive strength between GPIO and SIO pins in PSoC 3/5?
Not yet rated 		06/12/11
USBFS Not Appearing as Bootloader I/O in PSoC Creator
My USBFS component does not appear as the Bootloader I/O component in the Systems tab of design wide resources in PSoC Creator. How to solve this?
Not yet rated 		06/12/11
ISR connected to Timer Interrupt is being executed multiple times.
The ISR connected to Timer interrupts seems to get executed multiple times. Why is it so and how to solve this problem?
Not yet rated 		05/31/11
Calibrate the PSoC Internal Temperature Sensor
How do you calibrate the temperature of the FlashTemp user module?
Not yet rated 		05/29/11
Low to High transition on the TX pin during Reset
When using the UART (or TX8) user module, when the device gets reset, there is a Low to High transition on the TX pin. Why does this happen and what is the work around to avoid this transition?
Not yet rated 		05/24/11
Interrupts in M8C
How does an interrupt work in M8C controller?
Not yet rated 		03/28/11
UART Overrun Error
What is meant by Overrun error in UART and what considerations should be taken to overcome it?
Not yet rated 		03/27/11
INF file for HID device using USBFS user module
Does the PSoC Designer generate a .inf file when a HID device is created using the USBFS user module?
Not yet rated 		03/27/11
E2PROM Parameters and Map File
How does the locations of EEPROM User Module reflect in the Map file?
(4/5) by 1 user 		03/27/11
Clearing Counter/Timer/PWM Interrupt in PSoC 3/5
How do I clear the interrupt caused by Counter/Timer/PWM component so that the next interrupt is processed by the CPU?
(5/5) by 1 user 		03/23/11
Difference between the bWriteBytes functions in I2CHW and I2Cm user modules
How does the implementation of bWriteBytes function in I2CHW user module differ from the same API implementation in I2Cm user module?
Not yet rated 		03/21/11
Results 1 - 25 of 36 1  2   Next >
Sunset Owner: RAIK; Secondary Owner: GRAA;