Cypress Perform

Home > Support & Community
support.cypress.com     Bookmark and Share
Support & Community

Knowledge Base Search



Selected Type:  Digital

Keyword: Product: Application:  
Results 1 - 25 of 76 1  2   3   4   Next >
Title Customer Rating Updated
FX3 DVK Power Configurations - KBA83994
Question: Does the FX3 Development Kit (DVK) board support both self-powered and bus-powered configurations?
Not yet rated 		04/15/13
I2C Clock Stretching in FX2LP - KBA84113
Question: Does the FX2LP I2C controller support clock stretching?
Not yet rated 		04/15/13
Controlling PMODE Signals with an External Processor on FX3 DVK - KBA83992
Question: Can the PMODE signals be controlled by an external processor connected to the GPIF II interface on the FX3 Development Kit (DVK) board?
Not yet rated 		04/09/13
GPIO Toggle Frequency in EZ-USB FX3 - KBA83988
Question: How can I increase GPIO toggle frequency if I am using CyU3PGpioSetValue() and CyU3PGpioGetValue() with an EZ-USB FX3 device?
Not yet rated 		03/21/13
STA Warnings IN PSoC® 3 ES3/Production Release Silicons- KBA 84739
Question: Why do I get Static Timing Analysis (STA) warnings in my design for PSoC® 3 ES3 and Production release silicons and PSoC 5LP? I do not get these warnings if I port the project to PSoC 3 ES2 or PSoC 5.
Not yet rated 		12/06/12
Interfacing I2C EEPROM with using software I2C in PSoC 1
How do I interface an I2C EEPROM using I2C Master (software) User Module in PSoC1?
Not yet rated 		03/30/12
Implementation of OneShot
How do I implement a One-shot (Mono-shot) in PSoC 1?
Not yet rated 		03/29/12
Configuring E2PROM user module
How do I use an E2PROM user module in my project?
Not yet rated 		03/26/12
Interfacing PSoC1 to an SPI EEPROM
How do I interface PSoC1 to an external SPI EEPROM?
Not yet rated 		03/26/12
Interfacing an I2C EEPROM using I2CHW User Module
How do I interface the PSoC 1 to an external I2C EEPROM?
Not yet rated 		03/26/12
Implementing Half-duplex UART (using dynamic reconfiguration)
How do I implement a half –duplex UART using dynamic reconfiguration in PSoC 1?
Not yet rated 		03/26/12
I2CHW User module Slave operation
How to implement I2C slave using I2CHW user module in PSoC1?
Not yet rated 		03/23/12
Corruption in a particular location of nvSRAM even though WE# is pulled up to Vcc
Please explain the reason for corruption in a particular location of nvSRAM ( Typically 0x0000) even though WE# is pulled up to Vcc.
Not yet rated 		01/30/12
Generation of non-overlapping clocks (PWMs with Dead Band)
How to generate non-overlapping PWM signals in PSoC1?
Not yet rated 		01/24/12
IrDA stack in a PSoC
Is there an IrDA stack or a portion of the IrDA stack available for the PSoC1?
Not yet rated 		12/31/11
Multiple I2C Addresses in PSoC1
How can I implement multiple I²C addresses (multiple slaves) using only one I²C module?
Not yet rated 		12/31/11
Maximum I2C transaction length in PSoC
What is the maximum length of an I2C transaction in PSoC?
(4/5) by 1 user 		12/31/11
SPI bootloader in PSoC1
Why isn't there an SPI bootloader for PSoC1?
Not yet rated 		12/31/11
PWM and Counter - Difference
What is the difference between a PWM and a Counter User Modules?
(5/5) by 1 user 		12/30/11
UART Warning - 'UART should not be used along with a Power Setting that has SysClk freq less than 24MHz'
I am getting a warning message in my UART project: "Instance name-UART User Module-UART Configuration-lm6222: Level 1 Warning - UART should not be used along with a Power Setting that has SysClk freq less than 24MHz." Would you explain what this warning message means.
(4/5) by 1 user 		12/30/11
Maximum number of Full Duplex UARTs possible in a PSoC1
How many Full Duplex UARTs can be integrated in a PSoC1?
Not yet rated 		12/30/11
Transmitting 7 data bits + 1 Parity Bit using UART
Is it possible to transmit 7 data bits + 1 parity bit using the PSoC UART?
Not yet rated 		12/29/11
UART - Duty cycle of the Clock Input
Does the duty cycle of input clock to a UART affect the communication?
Not yet rated 		12/28/11
Programming the Almost Empty / Almost Full (PAE, PAF) Flags
- How do I program the PAE and PAF flags? - What is the valid range for PAE and PAF flags? - How do I store the PAE and PAF values?
Not yet rated 		12/28/11
Address pins in burst 4 mode of QDR SRAMS
How the address pins of QDR SRAMs are assigned, which pin is high bit, and which pin is low bit on the address bus?
Not yet rated 		12/28/11
Results 1 - 25 of 76 1  2   3   4   Next >
Sunset Owner: RAIK; Secondary Owner: GRAA;