Support & Community - Cypress Semiconductor

Knowledge Base Search

Selected Type: Analog
Keyword:	Product:	Application:

Results 1 - 25 of 80

1 2 3 4 Next >

Title	Customer Rating	Updated
Updating FIFOADR Signals in FX2LP™ - KBA85379 Question: Can I update FIFOADR signals in FX2LP?	Not yet rated	03/22/13
ESD Protection for EZ-USB® FX2LP™ - KBA85383 Question: Does FX2LP have ESD protection?	(5/5) by 1 user	03/22/13
Device Power Supply Levels in FX3 DVK – KBA84129 Question: Are the device power supply levels variable on the FX3 Development Kit (DVK) board?	Not yet rated	03/21/13
Using an External Battery for VBATT on FX3 DVK – KBA84130 Question: Can I use an external battery to power the VBATT domain on the FX3 Development Kit (DVK)?	Not yet rated	03/19/13
VDAC8 Output Voltage in PSoC® 3 and PSoC 5 - KBA84732 Question: The VDAC8 output does not go beyond 2.4 V even when the VDAC8 range is set to 4.080 V in PSoC® 3 and PSoC 5. What is the solution for this?	Not yet rated	12/07/12
ADC Performance with External Reference in PSoC® 3 and PSoC 5 - KBA 84753 Question: Does an external reference improve ADC performance?	(3/5) by 2 users	12/04/12
Driving an External Load using VDAC in PSoC® 3 or PSoC 5 - KBA83238 Question: How do I directly drive an external circuit using VDAC in PSoC 3 or PSoC 5?	(5/5) by 1 user	11/19/12
RESERVED Pin of FX2/FX2LP - KBA83346 Question:What should be done with the RESERVED pin of FX2/FX2LP?	Not yet rated	10/30/12
Best Method of Amplification to get Better Performance from PSoC® 3 OR PSoC 5 Del Sig ADC - KBA81866 Question: What are the different possible methods of amplification available for using with PSoC 3 or PSoC 5 Del Sig ADC? What is the best method of them to get better performance?	Not yet rated	10/03/12
PSoC® 3 Boost Inductor Size - KBA80957 Question: What size inductor should I use for the PSoC 3 boost circuit?	Not yet rated	07/13/12
ADC10 to measure 0 to 4V How do I implement a 10 bit Single Slope ADC (ADC10) in my PSoC 1 design?	Not yet rated	03/29/12
Implementation of DualADC. How do I implement a Dual ADC in my PSoC 1 design?	Not yet rated	03/29/12
Configuring Programmable threshold comparator How do I configure and implement a Programmable Threshold Comparator in my project?	Not yet rated	03/29/12
Using Incremental ADC to measure 0 to 5V How to use an Incremental ADC (ADCINCVR) User Module (UM) to measure analog signal?	Not yet rated	03/28/12
Signal Rectifier + Low Pass Filter Using PSoC® 1 How to use PSoC 1 as a Full wave rectifier / Low Pass Filter?	Not yet rated	03/24/12
Three OPAMP instrumentation amplifier Is there any instrumentation amplifier in PSoC1?	Not yet rated	03/01/12
PLL bandwidth and its impact on PLL output clock jitter What is PLL bandwidth and how does it impact PLL output jitter?	Not yet rated	12/27/11
Usage of dedicated IDAC pins What are the advantages of routing the IDAC’s output to the dedicated IDAC output pin instead of other GPIO pins?	Not yet rated	12/24/11
Affect of traces connecting the current sense resistors on current measurement accuracy Do the traces connecting the current sense resistors affect current measurement accuracy?	Not yet rated	12/05/11
Minimum On/Off timers in the Hysteretic Controller What is the importance of minimum on/off timers in the Hysteretic Controller block?	Not yet rated	12/05/11
Built-in Switching Regulator of the CY8CLED0xD/G0x Am I required to use the Built-in Switching Regulator of the CY8CLED0xD/G0x? If I am using the Built-in Switching Regulator, do I still connect the Vdd and AVdd? What are the component values used for the Built-in Switching Regulator?	Not yet rated	12/05/11
Kelvin connections for Sense resistor Why use Kelvin connections for Sense resistor?	Not yet rated	12/05/11
Measuring a microvolt signal using PSoC1 Can we measure a micro volt signal using PSoC1?	(2/5) by 1 user	12/05/11
SWX pin connection when internal FETs are not being used How should unused internal FET pins (SW0-SW3, pins 40, 37, 36, 33, respectively) be connected?	Not yet rated	12/05/11
Grounded current sensing using PowerPSoC Is it possible to implement grounded (Low-Side) current sensing using PowerPSoC?	Not yet rated	12/05/11

Results 1 - 25 of 80

1 2 3 4 Next >

Cypress Perform