Cypress Perform

Home > Support & Community
support.cypress.com     Bookmark and Share
Support & Community

Knowledge Base Search



Selected Type:  Protocols

Keyword: Product: Application:  
Results 1 - 25 of 60 1  2   3   Next >
Title Customer Rating Updated
Maximum I2C Speed at 3.3V - KBA85465
Question: What is the maximum communication speed of an I2C bus at 3.3V? Can I run the I2C at 400 kHz at 3.3V?
Not yet rated 		04/26/13
Startup I2C Clock Rate for EZ-USB® FX2LP™ - KBA85384
Question: Can I change the clock rate of the I2C device to 100 kHz after startup? Must it be 400 kHz at startup to properly enumerate?
Not yet rated 		03/22/13
I2C Read using FX2™ and FX2LP™ - KBA85382
Question: How is I2C read implemented in FX2 and FX2LP?
(4/5) by 1 user 		03/22/13
I2C Signals from FX3 DVK to an External I2C Device - KBA83996
Question: Can I route the I2C signals from the FX3 Development Kit (DVK) to an external I2C device?
Not yet rated 		03/19/13
Frequently Asked Questions about I2C lines - KBA85348

Not yet rated 		01/03/13
Different Modules of AgileHID for Wireless Devices - KBA82947
Question: Does the AgileHID protocol have different modules for wireless device (keyboard, mouse) and dongle?
Not yet rated 		10/11/12
Interfacing PSoC® 3/PSoC 5 with an Android Device - KBA83909
Question: Can the USB component in PSoC 3 work with an Android Device?
Not yet rated 		10/10/12
Configuring a CY8C201xx Device for Use Either with External Pull-ups or With a Master Operating at Different VDD – KBA80735
Question: What action must be taken to use a CY8C201xx device either with external pull-ups or with a master operating at different VDD?
Not yet rated 		07/03/12
Programming PSoC 1 using an I2C Bootloader
How to program a PSoC 1 MCU using an I2C interface?
Not yet rated 		03/24/12
Clock Stretching and I2C speed
How does the I2C clock speed affect the duration of clock stretching introduced by the I2C slave?
Not yet rated 		03/13/12
Series resistors on I2C lines
Why resistors of 330 ohm are required on I2C lines?
Not yet rated 		01/16/12
Hung state on FX2 due to I2C STOP Bit
Why does the FX2 firmware hangs when the STOP bit is set after polling for the STOP bit.
Not yet rated 		12/31/11
Why are the channels (78) in the channel subsets (13) using 6MHz spacing?
Why are the channels (78) in the channel subsets (13) using 6MHz spacing?
Not yet rated 		12/30/11
Waking up CY8C20xx6 using the I2C hardware address
How EzI2C UM (user module in PD5SP6 or earlier) can be modified so that the device (PSoC - CY8C20xx6) can be woken up from sleep by sending a targeted I2C read instruction from the master side.
Not yet rated 		12/28/11
Hub Ping mode
What is meant by Hub Ping mode in CyFi?
Not yet rated 		12/24/11
Hub Data Mode
What is meant by Hub Data Mode in CyFi?
Not yet rated 		12/24/11
Hub Bind mode
What is meant by Hub Bind mode in CyFi?
Not yet rated 		12/24/11
Node Unbind mechanism in CyFi
How does an Unbind mechanism of node take place in CyFi?
Not yet rated 		12/24/11
Node Bind mode
What is meant by Node Bind mode in CyFi?
Not yet rated 		12/24/11
First Channel and Last Channel of CyFi
What is the significance of the parameters First channel and Last channel in CyFi user module?
Not yet rated 		12/24/11
EEPROM block in CyFi Protocol
What is the need of EEPROM block in CyFi protocol?
Not yet rated 		12/24/11
BCD Payload Max in CyFi
What is BCD Payload MAX?
Not yet rated 		12/24/11
Node Connect Mode
What is Node Connect mode in CyFi Protocol stack?
Not yet rated 		12/24/11
Maximum number of Nodes in CyFi
How many nodes are supported by CyFi Protocol stack?
Not yet rated 		12/24/11
Node addressing in CyFi protocol
How is node addressing done in CyFi Protocol stack?
Not yet rated 		12/24/11
Results 1 - 25 of 60 1  2   3   Next >
Sunset Owner: RAIK; Secondary Owner: GRAA;