Support & Community - Cypress Semiconductor

Knowledge Base Search

Selected Type: Microcontrollers
Keyword:	Product:	Application:

Results 1 - 25 of 30

1 2 Next >

Title	Customer Rating	Updated
Can you read out an M8 OTP once it's programmed? Assuming the answer is YES how do I prevent this? Can you read out an M8 OTP once it's programmed? Assuming the answer is YES how do I prevent this?	Not yet rated	10/08/12
Clearing the INTOUTn line from a GPIO cell If I have an interrupt on edge, what clears the Interrupt Output (INTO) line from the GPIO cell?	Not yet rated	01/01/12
Operation with OHCI vs. UCHI host controllers I have a M8 chip in my device. My device works fine with UHCI host controller, but it fails with an OHCI host controller.	Not yet rated	10/02/11
Verifying my firmware checksum How can I verify my firmware checksum?	Not yet rated	10/02/11
In-circuit programming of M-8 chips How to program M8 Chips in-circuit?	Not yet rated	10/02/11
M8 Code Execution Time Is there an easy way to tell how much time a section of code takes to execute?	Not yet rated	10/02/11
Free-running timer on M8 parts The M8 controllers include a 12-bit timer that increments every microsecond. Is it possible to change the clock rate of this counter/timer?	Not yet rated	10/02/11
Difference between the M8A and M8B processors What is the difference between the M8A and M8B processors?	Not yet rated	10/02/11
ESD protection for the M8 chips Are the M8 chips protected asgainst ESD?	Not yet rated	10/02/11
Parts based on the M8B processor core Which parts are based on the M8B processor core?	Not yet rated	10/02/11
Programming Cypress' M8 family of parts How do I program Cypress' M8 family of parts?	Not yet rated	10/02/11
Parts based on the M8A processor core Which parts are based on the M8A processor core?	Not yet rated	10/02/11
M8 programming specifications How do we get the programming specifications for your M8 chips?	Not yet rated	10/02/11
Programming M8 microcontrollers How do I program the M8 microcontrollers?	Not yet rated	09/28/11
How does the lock bit of the CY7C63001a work? All programmers from HI LO have something called a "Lock Bit" option for code protection. Is there such a feature in the HI LO programmer supported by Cypress for the M8 parts?	Not yet rated	09/22/11
CYASM Assembler User Guide Where can i find CyASM and details about it?	Not yet rated	09/22/11
When I compile my firmware with the CYASM I get the following message: Error 'Jumps can not cross 4K boundary...' Why? When I compile my firmware with the CYASM, I get the following message: Error "Jumps can not cross 4K boundary..." Why?	Not yet rated	09/22/11
CYASM What is CYASM?	Not yet rated	09/22/11
Current version of CYASM What is the current version of CYASM?	Not yet rated	09/22/11
Bytecraft Compiler Error I receive "Compiler error: Jumps cannot cross 4K boundary". How can we prevent this failure?	Not yet rated	09/22/11
Tolerance on internal GPIO pull up/down resistance in PSoC 1/3/5 What is the tolerance of Pull Up/Down resistance on the GPIOs in PSoC 1/3/5 ?	Not yet rated	07/17/11
Toggling the CY7C64113's GPIO I would like to rapidly change the CY7C64113's GPIO lines between input and output to implement a bi-directional bus. Is there any problem in switching between in and out or is there a limit to the rate this can be done?	Not yet rated	06/22/11
Can 125us interrupt be generated in the CY7C64013 or CY7C64113? Using CY7C64013 or CY7C64113, how can I create a 125us interrupt?	Not yet rated	06/22/11
Config0 byte in I2C EEPROM showing bit 2 setting Why do some examples for the Config0 byte in I2C EEPROM show setting bit 2?	Not yet rated	03/29/11
Dynamic Switching of the FX2 CPU Clock. Is it possible to change clock frequency while the chip is running?	(5/5) by 1 user	03/29/11

Results 1 - 25 of 30

1 2 Next >

Cypress Perform