Cypress Perform

Home > Support & Community
support.cypress.com     Bookmark and Share
Support & Community

Knowledge Base Search



Selected Type:  All Knowledge Base Types

Keyword: Product: Application:  
Results 1 - 25 of 1521 2   3   4   5    ...  57   58   59   60   61   Next >
Title Customer Rating Updated
EZ-USB® HX2VL™ Mass Manufacturing Software Tool – KBA91293 New
Question: Which software tool can be used to program EZ-USB® HX2VL™ during mass manufacturing?

Not yet rated
04/24/14
Binding a USB-Serial Device to a Microsoft® CDC Driver – KBA91366 New
Question: How do you bind a USB Serial device configured as a USB-UART bridge to a Microsoft® Communication Device Class (CDC) driver?

Not yet rated
04/24/14
MaxPower Byte in Configuration Descriptors Versus HubController Power Byte in HUB Descriptors - KBA90630 New
Question: In the 0xD4 load of HX2LP™ what is the difference between Bytes 8 and 9 and Bytes 12 through 15?

Not yet rated
04/24/14
USB-UART Bridge Controller Not Appearing in the Device Manager Under Ports (Com & LPT) - KBA91228 New
Question: In the Host, the USB-UART bridge controller is enumerating properly and you can see the device under both “CypressUsbConsoleWindowsDriver” and Ports (COM & LPT), but sometimes you cannot see the device under Ports (COM & LPT) in the Device Manager. Why does this occur and how do you fix it?

Not yet rated
04/24/14
Differences Between the Microsoft® CDC Driver and the Cypress® CDC Driver - KBA91559 New
Question: What are the differences between the Microsoft® Communications Device Class (CDC) driver and the Cypress® CDC driver?

Not yet rated
04/24/14
Register Map for FX3 – KBA84136 Updated
Question: Where can I find the register map for FX3?

Not yet rated
04/23/14
FLAG Pin State of EZ-USB® FX1™/FX2™/FX2LP™ during a USB Bus Reset – KBA90546 Updated
Question: What is the state of the FLAG pins of EZ-USB® FX1™/FX2™/FX2LP™ during a USB bus reset? What will the state of the FLAG pins be after a USB bus reset?

Not yet rated
04/22/14
Capacitor Value on the VCCD Pin of USB-Serial Bridge Controllers - KBA91052 Updated
Question: What value of capacitance should be used on the VCCD pin of USB-Serial Bridge Controllers?

Not yet rated
04/22/14
Version of Linux Supported by EZ-OTG™/EZ-HOST™ – KBA91287 New
Question: What version of Linux is supported by EZ-OTG™/EZ-HOST™?

Not yet rated
04/22/14
Connecting PA6 of CY7C67200 – KBA91199 New
Question: How do you connect the A6 pin of CY7C67200 in the host application?

Not yet rated
04/21/14
Meaning of Error Codes in Control Center – KBA90827 New
Question: Where can you find the meaning of error codes in Control Center?

Not yet rated
04/21/14
Serial Number Requirement in the Descriptors of Unsigned Drivers – KBA90247 New
Question: After manually binding the device with its drivers it is working fine, but when you connect the device to another port the device appears as unknown in the Device Manager. Why is this happening? What is the solution?

Not yet rated
04/21/14
Crystal Drive Level Requirement for EZ-USB® FX2LP™ – KBA90549 New
Question: In FX2LP™, what does it mean to have a 500 μW crystal drive level requirement?

Not yet rated
04/21/14
RREF Resistor in EZ-USB® HX2VL™ – KBA90451
Question: What is the purpose of the RREF resistor in HX2VL™? Can you use a resistor with a value other than 649 Ω?

Not yet rated
04/15/14
Edge-Triggered Interrupt Using a GPIO – KBA91007
Question: Is it possible to use one of the USB-Serial device GPIOs (CY7C65211, CY7C65213, CY7C65215) as an edge-triggered interrupt?

Not yet rated
04/15/14
EZ-USB® FX2™/FX2LP™ Oscillator Is Not Running – KBA90541
Question: What should you check if the oscillator is not running on the FX2™/FX2LP™ board?

Not yet rated
04/15/14
Connecting a 5 V Logic to EZ-USB® FX2™/FX2LP™ Pins – KBA90543
Question: Can you connect a 5 V Logic to FX2™/FX2LP™ pins?

Not yet rated
04/15/14
Configuring EP1 as an IN or OUT in EZ-USB® FX2LP™ – KBA90544
Question: Is it possible to configure EP1 as both IN and OUT in FX2LP™?

Not yet rated
04/15/14
Streaming Application Example in EZ-USB® FX2™ and FX2LP™ – KBA90545
Question: Do FX2™ and FX2LP™ support streaming data transfer?

Not yet rated
04/15/14
Internal Pull-Up or Pull-Down on Port I/O Pins in EZ-USB® FX2™/FX2LP™ – KBA90548
Question: Are there any weak internal pull-up or pull-down resistors on the FX2™/FX2LP™ port pins?

Not yet rated
04/15/14
Enumeration of EZ-USB® FX2LP™ – KBA91305
Question: If both a small EEPROM and a large EEPROM are connected to FX2LP™, then from which EEPROM does the device enumerate?

Not yet rated
04/15/14
Interfacing an External I2C Device with the CYUSBS234/236 DVK – KBA91299
Question: How can you connect an external I2C device to the CYUSBS234/236 DVK?

Not yet rated
04/14/14
Configuring SL811 to Support a Low-Speed Device Connected to a Full-Speed Hub – KBA91288
Question: How do you set SL811 to support a low-speed device connected to SL811 via a full-speed hub?

Not yet rated
04/14/14
How to design with FX3/FX3S – KBA87889
Question: Can you give me a comprehensive list of resources that I can use to design applications using FX3/FX3S?

Not yet rated
04/11/14
CX3 Firmware: Frequently Asked Questions – KBA91297

Not yet rated
04/11/14
Results 1 - 25 of 1521 2   3   4   5    ...  57   58   59   60   61   Next >
Sunset Owner: RAIK; Secondary Owner: GRAA;