|
Title
|
Customer Rating
|
Updated
|
Communication distance of the Cypress PLC High Voltage Solution
What is the longest distance that the Cypress PLC High Voltage Solution can communicate over?
|
Not yet rated
|
12/05/11 |
Transmitting between phases using PLC
Can the PLC signal transmitted from one phase be received by a node on another phase?
|
Not yet rated
|
12/05/11 |
Maximum and minimum input pin hysteresis for powerline communication products
What is the maximum and minimum input pin hysteresis for the powerline communication products?
|
Not yet rated
|
12/05/11 |
Connecting the GDVdd, Vdd, and AVdd when using the Built-in Switching Regulator
If I am using the Built-in Switching Regulator, do I still connect the GDVdd, Vdd, and AVdd?
|
Not yet rated
|
12/05/11 |
Component values used for the Built-in Switching Regulator
What is the component values used for the Built-in Switching Regulator?
|
Not yet rated
|
12/05/11 |
Calculating upper and lower DAC references for a hysteretic controller of PowerPSoC device
How can one calculate upper and lower DAC references for a hysteretic controller of PowerPSoC device?
|
Not yet rated
|
12/05/11 |
Information needed to implement binning compensation for LED
What data do I need from LED vendors for implementing binning compensation?
|
Not yet rated
|
12/05/11 |
Single INF file that supports both device and script in Windows XP 32 and 64 bit for FX1/FX2LP
Can you provide the single INF that supports both device and script in Windows XP 32 and 64 bit?
|
(3.5/5) by 2
users
|
12/05/11 |
CY3261 firmware and RGB software
Where is the CY3261 kit documentation available ?
|
(5/5) by 1
user
|
12/05/11 |
Dynamically changing the CSA input multiplexed to the AINX
Is it possible to dynamically change the CSA input that is multiplexed to the AINX (Analog Input Multiplexer)?
|
(5/5) by 1
user
|
12/05/11 |
What is the CY3654-P02?
What is the CY3654-P02?
|
Not yet rated
|
12/05/11 |
PLC communication when the powerline is off
With the PLT transceiver, would the communication still work if the power on the powerline goes off?
|
(5/5) by 1
user
|
12/05/11 |
Common Anode configuration with PowerPSoC
Is a common anode LED configuration possible with PowerPSoC?
|
Not yet rated
|
12/05/11 |
GPIO pins available in CY3267 board.
On the CY3267 development kit, is there any GPIO pin brought out that is capable of Analog I/O?
|
Not yet rated
|
12/05/11 |
FN0 pins as GPIO pins.
Can the FN0 pins be used as GPIO pins?
|
Not yet rated
|
12/05/11 |
Internal and External FET control.
Is it possible to control both the external and internal FET simultaneously with the same Hysteretic controllers?
|
Not yet rated
|
12/05/11 |
The role of CY8C24894 in the CY3267 board.
What are the functions implemented by the CY8C24894 on the CY3267 board?
|
Not yet rated
|
12/05/11 |
Counter And Compartor for More Than One PrISM Block
If more than one PrISM user module is instantiated for intensity control, do they share a global counter and comparator?
|
Not yet rated
|
12/05/11 |
Measurement of Current values from CSA block in PowerPSoC
How do I measure the current strength values from the CSA blocks used in regulators inside PPSoC?
|
(4/5) by 2
users
|
12/05/11 |
Driving external FETs using the FN0 pins.
Is it possible to control the SW FETs directly from one of the FN pins of CY8CLED04D01?
|
Not yet rated
|
12/05/11 |
CY3267 Kit documentation
Where will I get the documentation for CY3267 kit?
|
Not yet rated
|
12/05/11 |
CY3268 Kit documentation
Where will I get the documentation for CY3268 kit?
|
Not yet rated
|
12/05/11 |
SWX pin connection when internal FETs are not being used
How should unused internal FET pins (SW0-SW3, pins 40, 37, 36, 33, respectively) be connected?
|
Not yet rated
|
12/05/11 |
Grounded current sensing using PowerPSoC
Is it possible to implement grounded (Low-Side) current sensing using PowerPSoC?
|
Not yet rated
|
12/05/11 |
Time between calls to PLT_Poll
How often do I need to call the PLT_Poll() function?
|
Not yet rated
|
12/05/11 |
Clocking Options for the PLT user module
What are the available clocking options for the PLT user module?
|
Not yet rated
|
12/05/11 |
Setting the parameters for the PLT user module
How do I set the parameters in the PLT user module?
|
Not yet rated
|
12/05/11 |
License Key for PLT user module
When I try to place the PLT user module, I am asked for a license key. How do I get this key?
|
(5/5) by 4
users
|
12/05/11 |
Sending instant messages using Control Panel GUI
How does the Control Panel GUI work for instant messages?
|
Not yet rated
|
12/05/11 |
Load/Save configuration in the Control Panel GUI
How does the load/save configuration in the Control Panel GUI work?
|
Not yet rated
|
12/05/11 |
Controlling more than 2 PLC nodes using the Control Panel GUI
How can I control more than 2 PLC nodes using the Control Panel GUI on 1 PC?
|
Not yet rated
|
12/05/11 |
Use of Control Panel GUI
Where can I use the Control Panel GUI?
|
Not yet rated
|
12/05/11 |
Start up guidelines for PowerPSoC based system
What are the steps to bring-up a newly fabricated PowerPSoC based system?
|
Not yet rated
|
12/05/11 |
SSDM_Polarity in System Level project
How to invert the "SSDM_Polarity" in System Level project of PSoC Designer 5.0?
|
Not yet rated
|
12/05/11 |
CY22395 S0 & S1 Signals
When creating a *.jed file with CyClockRT, there seems to be no place in the GUI to set S0 and S1. How can these be set in the bitmap?
|
Not yet rated
|
12/05/11 |
In-System Reprogrammable Clocks Vs Programmable Clocks
What is the main difference between In-System Reprogrammable Clocks and normal Programmable Clocks apart from the differences found in the datasheets?
|
Not yet rated
|
12/05/11 |
Error in Opening a Project (created in PD5.1 SP2) on PD5.1 SP2 Installer Hotfix version
Why I cannot open the project created using PD5.1 SP2 on PD5.1 SP2 Installer Hotfix version?
|
(5/5) by 1
user
|
12/02/11 |
Upgrading the 4-Meg (CY7C0852V/AV) Dual-Port to a 9-Meg (CY7C0853V/AV) Dual-Port
What are the pin considerations while upgrading from a 4-Meg (CY7C0852V/AV) Dual-Port to a 9-Meg (CY7C0853V/AV) Dual-Port?
|
Not yet rated
|
12/01/11 |
Programming tool for Capsense Express device - CY8C201xx
What are the qualified programming/config tools for Capsense Express devices for Mass production?
|
Not yet rated
|
11/30/11 |
Number of programming cycles for CY254xx family of devices
How many times can the CY254xx family of field and factory programmable devices can be programmed? Devices include: CY2542, CY2544, CY2545, CY2546, CY2547, CY2548, CY25402, CY25403, CY25404, CY25422, CY25423, CY25482, and CY25483.
|
Not yet rated
|
11/30/11 |
RTOS Support in PSoC 3
Is there RTOS support for PSoC 3, for example RTX51?
|
Not yet rated
|
11/30/11 |
1-wire Slave Device Support
Can PSoC act as a 1-wire slave device while using the 1-wire user module?
|
Not yet rated
|
11/30/11 |
USB HID joystick sample code for the EZ-USB
Where I can get HID joystick sample firmware for the EZ-USB chips?
|
Not yet rated
|
11/29/11 |
Using internal voltage regulator for enCoRe II
How can I use the enCoRe II internal voltage regulator?
|
Not yet rated
|
11/29/11 |
DTMF Decoder
How do I implement DTMF Decoder in PSoC1 ? I can't find the DTMF Decoder User Module available in PSoC1.
|
Not yet rated
|
11/29/11 |
Maximum Transfer Rate of the SX2 Data Bus
What is the maximum transfer rate of the SX2 data bus?
|
Not yet rated
|
11/29/11 |
Header pins in EZ-USB (AN21xx/FX/FX1/FX2/FX2LP) Development kit
Why are there header pins on the EZ-USB (AN21xx/FX/FX1/FX2/FX2LP) development board and what purpose do they serve?
|
Not yet rated
|
11/29/11 |
CapSense_CSD Tuner Set Up
Why CapSense tuner I2C communication fails even if I have configured my hardware properly?
|
Not yet rated
|
11/29/11 |
I cannot install CY8C28 kit collateral from the PSoC 1 CD available in CY8CKIT001B Rev **
How can I install CY8C28 kit collateral from the PSoC 1 CD available in CY8CKIT001B Rev ** ?
|
Not yet rated
|
11/29/11 |
Which SMPTE standards does the original HOTLink family support/not support?
|
Not yet rated
|
11/29/11 |