|
Title
|
Customer Rating
|
Updated
|
Effect of series resistor on raw counts of the sensor
In a CapSense application, does change in series resistors cause a change in raw-counts?
|
Not yet rated
|
03/13/12 |
Maximum allowed noise in CapSense
What is the maximum value of noise allowed in a CapSense application?
|
Not yet rated
|
03/13/12 |
Accuracy of switching/precharge clocks used in CSD
|
Not yet rated
|
03/13/12 |
CY8C20X36A/46A/66A/96A: ISSUE WITH SHARING ISSP BUS
Why CY8C20X36A/46A/66A/96A parts get heated up abnormally while in reset and when trying to program another PSoC chip on a shared ISSP bus?
|
Not yet rated
|
03/13/12 |
Drift in raw counts over a period of time
Is there any change in raw counts for a sensor over a period of time?
|
Not yet rated
|
03/13/12 |
ADC gives incorrect value when CapSense is enabled
When input to an ADC is taken from a MUX bus and if CapSense is enabled, the ADC produces incorrect results? What is the reason for this error and how can this be corrected?
|
Not yet rated
|
03/13/12 |
Vih and Vil values when LDO enabled in CY8C20X66
If LDO on port 1 of CY8C20X66 is enabled for 1.8V, output signal levels(Voh, Vol) will be as per 1.8V Vdd, but what will be the input signal voltage specs(Vil, Vih)?
|
Not yet rated
|
03/13/12 |
Capsense Power Consumption
How to calculate the average power consumption for capsense devices?
|
Not yet rated
|
03/13/12 |
CY3217-MiniProg1 Electrostatic discharge (ESD) Resistance
How resistant is the CY3217-MiniProg1 kit to ESD noise?
|
Not yet rated
|
02/02/12 |
CY8C20xx7 family CapSense Controller does not provide on-chip debug (OCD) support
Does CY8C20xx7 family CapSense Controller provide on-chip debug (OCD) support?
|
Not yet rated
|
02/02/12 |
Settling time
What is settling time?
How to set the settling time for a capsense project?
|
Not yet rated
|
01/16/12 |
CapSense wake up on finger touch
Can I make a design in a such a way that the CapSense PSoC wakes up from sleep when the finger touch us detected
|
Not yet rated
|
01/01/12 |
LED backlight support in capsense
Does capsense support LED backlighting ?
|
Not yet rated
|
01/01/12 |
Heat seal paper in Capsense
Can a heat seal paper be used in CapSense applications?
|
Not yet rated
|
01/01/12 |
Slow slider response
My slider response is very slow if the sysClk is 6MHz. How can I make the response faster?
|
Not yet rated
|
01/01/12 |
two rings surrounding thermal pad of CY8C20434-12LKXI (32 QFN)
There are two rings surrounding the thermal pad on the bottom of the chip. Is it safe if they are all connected together (soldered in manufacturing)?
|
Not yet rated
|
01/01/12 |
Who should I get in touch with to obtain pricing and availability information?
Who should I get in touch with to obtain pricing and availability information?
|
Not yet rated
|
12/30/11 |
UART Communication on CY8C20436
Is it possible to include UART functionality in addition to touch button, CSD function on CY8C20xx6 devices?
|
Not yet rated
|
12/28/11 |
Waking up CY8C20xx6 using the I2C hardware address
How EzI2C UM (user module in PD5SP6 or earlier) can be modified so that the device (PSoC - CY8C20xx6) can be woken up from sleep by sending a targeted I2C read instruction from the master side.
|
Not yet rated
|
12/28/11 |
Air Gap between Capsense Sensor and an Overlay
Can there be an air gap between a Capsense sensor and an Overlay?
|
Not yet rated
|
12/07/11 |
Programming tool for Capsense Express device - CY8C201xx
What are the qualified programming/config tools for Capsense Express devices for Mass production?
|
Not yet rated
|
11/30/11 |
Export data option doesn't work in CapSense Express Tuner
Export data option doesn't work in CapSense Express Tuner window of PSoC Designer 5.0 SP6
|
Not yet rated
|
11/09/11 |
CapSense sensor scan time mentioned in CSD2X user module datasheet does not match with measurement from hardware
Why does the CapSense sensor scan time mentioned in CSD2X user module datasheet does not match with measurement from hardware?
|
Not yet rated
|
11/03/11 |
Moisture Sensitivity Level (MSL) of Cypress Parts
How do I find Moisture Sensitivity Level (MSL) of Cypress parts?
|
Not yet rated
|
09/08/11 |
MiniProg3 can't program my device in XRES mode
Why is MiniProg3 not able to program my board in Reset mode even though the board is powered externally?
|
Not yet rated
|
08/05/11 |
Routing 32 KHz ILO output to pin in CY8C20xx6A
Is it possible to route 32kHz ILO output to the pin in Cy8C20xx6A series of devices?
|
Not yet rated
|
06/26/11 |
Upgrading CapSense projects to PSoC Designer5.0 SP5.0 or higher
When I upgrade PSoC Designer 5.0 to SP5.0 or higher, CapSense (In devices CY8C20x34, CY8C20x46, or CY8C20x66) does not work properly. What may be the reason?
|
Not yet rated
|
06/26/11 |
Ok and Cancel Options missing from CSD wizard
Why am I not finding OK and Cancel options in the CSD wizard?
|
Not yet rated
|
06/19/11 |
Bringing out Shield Electrode in System Level Design for Capsense CSD
Is it possible to set the Shield Electrode option for CSD user module in System level design?
|
(5/5) by 1
user
|
06/19/11 |
Upgrading CapSense projects to PSoC Designer5.0 SP5.0 or higher
When I upgrade PSoC Designer 5.0 to SP5.0 or higher, CapSense (In devices CY8C20x34, CY8C20x46, or CY8C20x66) does not work properly. What may be the reason?
|
Not yet rated
|
06/19/11 |
Minimum Supply Voltage to PSoC 1
What is the minimum operating supply voltage that can be provided to PSoC1 devices ?
|
Not yet rated
|
06/15/11 |
Minimum PWM frequency in System level design
What minimum PWM frequency can be configured in System level design?
|
Not yet rated
|
06/13/11 |
CSD Parasitic Capacitance Calculator
How can I find the Parasitic Capacitance of my sensor from the raw counts? I am using CY8C21x34.
|
Not yet rated
|
06/13/11 |
Proximity sensing using CSD
How to configure a proximity sensor with CSD UM?
|
Not yet rated
|
06/03/11 |
I2C clock frequency of CapSense Exress device
What is the frequency at which I2C slave is configured in CapSense Express devices?
|
(3/5) by 2
users
|
04/01/11 |
User defined area in CapSense Express device
Is it possible to store your own data like firmware version in the register space of CapSense Express device?
|
Not yet rated
|
04/01/11 |
Can slider segments be used as capsense buttons?
Can I use the 7 segments slider on first touch kit as 7 different switches?
|
Not yet rated
|
03/28/11 |
Default I2C slave address of CY8C20110
What is the default I2C slave address of any CapSense Express device?
|
Not yet rated
|
03/28/11 |
DAC on a CY8C21x34
How do I configure an SC Block as a DAC in CY8C21x34 as there is no option of configuring ASE type switch capacitor blocks as DACs ?
|
Not yet rated
|
03/28/11 |
Difference between CY8C21434-24LTXI and CY8C21434-24LFXI
What is the difference between CY8C21434-24LTXI and CY8C21434-24LFXI parts?
|
Not yet rated
|
03/27/11 |
Design Considerations for Using PSoC in a Noisy Environment
What should be the design considerations for using PSoC1 in Noisy environment ?
|
Not yet rated
|
03/26/11 |
Selecting CY8C24094 part in PSoC Designer
Why can't I find the part number CY8C24094-24AXI, which is on CY3214 development kit, in PSoC Designer?
|
Not yet rated
|
03/24/11 |
Implementing Capsense CSD and ADC simultaneously
I would like to implement Capsense CSD and ADCINC/DelSig ADC simultaneously in a PSoC1, but PSoC Designer does not allow this. How do I implement both the functions ?
|
Not yet rated
|
03/24/11 |
PSoC ESD/EMC Resistance
How resistant is the PSoC to ESD/EMC noise?
|
Not yet rated
|
03/20/11 |
ESD information
What is the ESD tolerance of PSoC GPIO?
|
Not yet rated
|
03/20/11 |
Filtering LCD noise (Back Light Inverter Noise)
How do I filter out the LCD inverter noise in Capsense?
|
Not yet rated
|
03/10/11 |
Effect of external DC voltage on CapSense sensors
What if the electrodes have a small DC voltage on them, will this affect CapSense? What is the range of this voltage that the devices can handle?
|
Not yet rated
|
03/10/11 |
Overlay material for high ESD (>25KV) environment
What overlay materials do you recommend for a high (>25KV) ESD environment. Are there other design techniques for this environment?
|
Not yet rated
|
03/10/11 |
Monitoring Function in PSoC Designer System Level Design
Can I utilize monitoring function in PSoC Designer System Level design for FirstTouch Kit?
|
(1/5) by 1
user
|
02/27/11 |
PCB coating in CapSense
In CapSense desings, can varnish be used for PCB coating?
|
Not yet rated
|
02/26/11 |