Cypress Perform

Home > Products > USB Controllers

USB Controllers

Related Resource Results: Knowledge Base Articles
Keyword: Application: Language:  
      Click to subscribe to RSS

Results 1 - 50 of 1049 1  2   3   4   5   6   7   8   9   10   11   12   13   14   15   16   17   18   19   20   21   Next>
Title Customer Rating Updated
Reset Problems When Re-programming the 24LC64 EEPROM on the FX2 - KBA83436
Question: When an iic firmware image is created with the command hex2bix -i -o test.iic test.hex, the firmware does not get loaded and the device does not enumerate with the new descriptors as expected. What is the reason?
Not yet rated 		01/31/13
How to Interface FPGA to Ez-USB® FX3™ DVK (Rev 3) - KBA85373
Question: How to interface FPGA to FX3 DVK (Rev 3) Boards?
Not yet rated 		01/10/13
Downloading the firmware to FX2 chip.
What are my options of downloading the firmware to the chip.
Not yet rated 		12/21/12
Maximum throughput using FX3 - KBA84084
Question:What is the maximum throughput that can be obtained using FX3?
Not yet rated 		12/20/12
Maximum throughput using Bulk Source Sink Example - KBA84083
Question: How to obtain maximum throughput using bulk source sink example provided with FX3 SDK?
Not yet rated 		12/20/12
Building Custom .nx2 File - KBA83970
Question: How do I build a new .nx2 file?
(2/5) by 1 user 		12/20/12
Utilization of the Unused GPIF Control Lines - KBA83964
Question: Does triggering of the GPIF change the state of the unused control lines?
Not yet rated 		12/20/12
FX2LP does not enumerate for Firmware (code+xdata) of Size Greater than 16 K - KBA83973
Question: FX2LP does not enumerate when firmware (code+xdata) of size greater than 16 K is downloaded. Why is this happening?
Not yet rated 		12/20/12
Multiple FX2LP Devices Connected to Host - KBA83974
Question: How can the host distinguish between and communicate with multiple FX2LP devices connected if each of the devices have the same VID/PID?
Not yet rated 		12/20/12
USB Selective Suspend Compliance Test - KBA84678
Question: How to ensure that the enCoRe MCU based USB devices pass the USB selective suspend compliance test?
Not yet rated 		11/21/12
RESERVED Pin of FX2/FX2LP - KBA83346
Question:What should be done with the RESERVED pin of FX2/FX2LP?
Not yet rated 		10/30/12
Gerber Files of CY3684 FX2LP Development Kit – KBA83343
Question: Where can I find the Gerber files of CY3684 FX2LP Development kit?
Not yet rated 		10/30/12
Can AT2LP be used for SATA Drives - KBA83342
Question: Can AT2LP be used for SATA drives?
Not yet rated 		10/25/12
FX1/FX2LP - Vendor Request Example - KBA82848
Question: Are there examples on how to use the vendor commands with EZ-USB FX1/FX2LP?
Not yet rated 		10/18/12
To Detect When a Self-Powered USB Device is Plugged - KBA82850
Question: How do I detect when a self-powered USB device is plugged in?
Not yet rated 		10/11/12
C Compiler for FX2/FX2LP - KBA82844
Question: Does Cypress provide C compiler for FX1/FX2LP?
Not yet rated 		10/11/12
No drive letter appears when binding NX2LP/NX2LP-Flex/AT2/AT2LP device to Cypress manufacturing drivers
When NX2LP/NX2LP-Flex/AT2/AT2LP device is bound to cypress manufacturing driver no drive letter appears in windows. Why?
Not yet rated 		10/10/12
In-System EEPROM Programming for CY7C65620/30 - KBA82845
Question: Is there any program from a PC to in-system EEPROM programming to connect to the CY7C65620/30 hub? If so, how does this programming work?
Not yet rated 		10/10/12
For HX2LP OVR# Pins, Whether They Have an Internal Pull-up Resistor or Need an External Pull-up - KBA82846
Question: The HX2LP datasheet states a default state of '1' for the OVR# pins. Do they have an internal pull-up resistor or do we need an external pull-up if the pins are not used?
Not yet rated 		10/10/12
Changing the Device Class of the CY7C64225 USB to UART Bridge Controller - KBA81842
Question: Can I make the Cypress USB to UART bridge controller appear as a different device class?
Not yet rated 		08/17/12
Changing the Default VID/PID of the CY7C64225 USB to UART Bridge Controller - KBA81841
Question: How do I change the default VID/PID of the CY7C64225 USB to UART bridge controller?
Not yet rated 		08/17/12
Using a CY7C64225 USB to UART Bridge Controller in a Customer Application with the Cypress VID - KBA81840
Question: Can I use the Cypress VID for my own product?
Not yet rated 		08/17/12
Using a CY7C64225 USB to UART Bridge Controller in Mixed Modes - KBA81839
Question: Can a Cypress USB to UART bridge controller be powered in a mixed mode (i.e. both self-powered and bus powered)?
Not yet rated 		08/17/12
Baud Rates with a CY7C64225 USB to UART Bridge Controller - KBA81838
Question: What baud rates are achievable with a Cypress USB to UART bridge controller?
Not yet rated 		08/17/12
Using CY7C64225 USB to UART Bridge Controller with Mac OS - KBA81837
Question: Can I use a USB to UART bridge controller with Mac OS?
Not yet rated 		08/17/12
Using CY7C64225 USB to UART Bridge Controller with LINUX - KBA81835
Question: Can I use a Cypress USB to UART bridge controller with Linux?
Not yet rated 		08/17/12
Using CY7C64225 USB to UART Bridge Controller with Android - KBA81836
Question: Can I use a Cypress USB to UART bridge controller with Android?
Not yet rated 		08/17/12
Windows Hardware Certification Process for Customer Modified Cypress USB Driver Files
Windows Hardware Certification Process for Customer Modified Cypress USB Driver Files
Not yet rated 		07/10/12
Cypress Parts Baking Condition Information
Do Cypress parts require baking? If so, what are the conditions?
Not yet rated 		05/24/12
Country of Origin (COO) Information
Where can I find the Country of Origin (COO) of a Cypress product?
Not yet rated 		05/24/12
Windows 7/vista 64-bit ?Unable to find signed driver
When binding my device to CyUSB.sys in Windows 7/Vista 64-bit environment I get the following error ?Windows encountered a problem installing the driver software for your device?. What does this error mean? How can it be resolved?
Not yet rated 		05/07/12
ACM mode of FX2LP
Can the CY7C68013A (FX2LP) be programmed to act in CDC/ACM device?
Not yet rated 		04/30/12
SX2's response to SET_INTERFACE request
How is SX2's response to SET_INTERFACE request different from its response to other EP0 requests ?
Not yet rated 		04/30/12
SPI with 32 bit GPIF in FX3
Can SPI be used with GPIF II 32 bit in FX3?
Not yet rated 		04/26/12
Linux support for FX3
Does FX3 support Linux OS?
Not yet rated 		04/26/12
GPIO toggle frequency in FX3
How can I increase GPIO toggle frequency obtained using APIs CyU3PGpioSetValue() and CyU3PGpioGetValue() in FX3?
Not yet rated 		04/26/12
Test pins in FX3
What is the function of test pins in FX3?
Not yet rated 		04/26/12
Watchdog timer
What are the clock sources for watchdog timer in FX3?
Not yet rated 		04/26/12
64 bit driver for FX3
Where do I obtain 64 bit driver for FX3?
Not yet rated 		04/26/12
Recommended Reflow for Cypress Parts Information
What is Cypress’s Parts Recommended Reflow?
Not yet rated 		04/20/12
Cypress' Parts Shelf Life Condition Information
What is Cypress’s Parts Shelf Life condition?
Not yet rated 		04/19/12
External hard reset requirement for FX3
The FX3 data sheet specifies that "an external hard reset should be provided after power on reset [POR]". Does it mean that the POR circuit should provide two reset pulses?
Not yet rated 		04/17/12
Handling Vendor/Class Request in the FX3
How the Vendor/Class Request is handled in the FX3 ?
Not yet rated 		04/10/12
GPIO configuration in FX3
How can i use the GPIF pins as GPIOs in FX3?
Not yet rated 		04/10/12
Electrical specification of USB interface of FX2LP
Where can the electrical specification of the USB interface of FX2LP be found?
Not yet rated 		03/13/12
IBIS model of CY7C6801XA
Please provide the IBIS model of CY7C6801XA. It is given in .txt format in Vendor web site.
Not yet rated 		03/13/12
FX2 Header Files
Where can I find the header files associated with EZ-USB FX2LP?
Not yet rated 		03/13/12
CYSTART - Current Version
What is the current version of CYSTART?
Not yet rated 		03/06/12
Errors or blank Check fails while using CY3649 Hi-Lo programmer
I get errors when programming using CY3649 Hi-Lo programmer (or) Blank Check fails when using CY3649 for programming Cypress M8 based microcontrollers (or) Different checksums are read from a BLANK device when using the CY3649
Not yet rated 		03/06/12
GPIF.exe and GPIF Designer.exe
What are GPIF.exe and GPIF Designer.exe used for?
Not yet rated 		03/06/12
Results 1 - 50 of 1049 1  2   3   4   5   6   7   8   9   10   11   12   13   14   15   16   17   18   19   20   21   Next>