|
Title
|
Customer Rating
|
Updated
|
Error - Could not detect pod - KBA85339
Question: When I try to either connect to the ICE or download code to the pod, I get the error message "Could not detect pod," in PSoC Designer. What are the points to be taken care of to avoid this error?
|
Not yet rated
|
03/19/13 |
PSoC® 1 Application Note Finder - KBA83025
PSoC1 Application Note Finder
|
(4/5) by 1
user
|
03/19/13 |
Pseudo Random Sequence Generator with PSoC® 1 - KBA83078
Question: How do I generate a random number sequence using PSoC® 1?
|
Not yet rated
|
03/19/13 |
Minimum Duration of XRES in PSoC® 1 - KBA83481
Question: What is the minimum duration of XRES that will reset a PSoC® 1 device?
|
Not yet rated
|
02/15/13 |
Definitions of INL and DNL in an ADC
What does INL and DNL mean in an ADC ?
|
(4.5/5) by 2
users
|
02/13/13 |
Source/Sink Resistance of PSoC® 1 GPIO - KBA83806
Question: What are the source and sink resistances of PSoC 1 GPIO configured in strong drive mode?
|
Not yet rated
|
10/18/12 |
Comparator Generating Multiple Interrupts
My comparator is triggering multiple interrupts. What could be the reason and how to prevent the same?
|
Not yet rated
|
08/03/12 |
ADC10 to measure 0 to 4V
How do I implement a 10 bit Single Slope ADC (ADC10) in my PSoC 1 design?
|
Not yet rated
|
03/29/12 |
Configuring Programmable threshold comparator
How do I configure and implement a Programmable Threshold Comparator in my project?
|
Not yet rated
|
03/29/12 |
Float to ASCII conversion
How to convert float number to ASCII for displaying on LCD ?
|
Not yet rated
|
03/28/12 |
Configuring E2PROM user module
How do I use an E2PROM user module in my project?
|
Not yet rated
|
03/26/12 |
Clock Stretching and I2C speed
How does the I2C clock speed affect the duration of clock stretching introduced by the I2C slave?
|
Not yet rated
|
03/13/12 |
CY3217-MiniProg1 Electrostatic discharge (ESD) Resistance
How resistant is the CY3217-MiniProg1 kit to ESD noise?
|
Not yet rated
|
02/02/12 |
'Uninitialised Interconnect View' Message - SVG viewer
What do I do when I get the message 'Uninitialized Interconnect View' when I go to the interconnect view of PSoC designer?
|
(5/5) by 1
user
|
02/02/12 |
Generation of sine wave in PSoC1
How can we generate a Sine Wave in PSoC1?
|
Not yet rated
|
01/25/12 |
Generation of non-overlapping clocks (PWMs with Dead Band)
How to generate non-overlapping PWM signals in PSoC1?
|
Not yet rated
|
01/24/12 |
CY3280-22X45 DVK
Why GPIO P1.7 in CY3280-22X45 DVK is not working properly?
|
Not yet rated
|
01/03/12 |
Custom boot.tpl. from PD 4.3 to PD 4.4
As of 4.3 I was able to extensively customize our boot.tpl files. However, in Psoc Designer 4.4 when I open the project it wants to create a new boot.tpl. If I let it, of course I lose my custom boot.tpl. If I click Cancel, it lets me keep it but refuses to do the "generate application" step. OK, I've noticed that I can re-enable the button by editing the project settings. How to solve this problem?
|
Not yet rated
|
01/01/12 |
Clear a Pending Interrupt
Section B:5 'Interrupt Controller' of the Technical Reference Manual says that an interrupt stays pending until it is serviced. What needs to be done to 'service' the interrupt? Also, what is it that actually clears the pending interrupt?
|
Not yet rated
|
01/01/12 |
Clearing the INTOUTn line from a GPIO cell
If I have an interrupt on edge, what clears the Interrupt Output (INTO) line from the GPIO cell?
|
Not yet rated
|
01/01/12 |
Getting error message: "cannot detect a pod"
I am getting error message: "Cannot detect a pod". How to remove it?
|
(4/5) by 1
user
|
01/01/12 |
CY4636 Mouse Fails to Bind
When the CY4636 Mouse is reprogrammed it cannot bind with the USB transceiver?
|
Not yet rated
|
12/30/11 |
CSD Wizard option disabled
When I right click on the CSD user module in my project, the CSD Wizard option is disabled. How do I enable the CSD wizard?
|
Not yet rated
|
12/29/11 |
1-wire Slave Device Support
Can PSoC act as a 1-wire slave device while using the 1-wire user module?
|
Not yet rated
|
11/30/11 |
DTMF Decoder
How do I implement DTMF Decoder in PSoC1 ? I can't find the DTMF Decoder User Module available in PSoC1.
|
Not yet rated
|
11/29/11 |
Avaliability of read out programmable file using PSoC Programmer read function
Can the read out data from read function of PSoC Programmer be saved as .hex file to program another PSoC devices?
|
Not yet rated
|
11/25/11 |
Calculating the current consumption of a PSoC1
How do I calculate the current consumption of a PSoC1 device?
|
Not yet rated
|
11/23/11 |
Choosing an I2C slave in PSoC1
Under what application needs should we use I2CHW slave and under what needs should we use EzI2Cs slave ?
|
Not yet rated
|
11/17/11 |
Flash read/write access from firmware in PSoC1 devices
How Can we read and write to flash in the PSoC1 devices?
|
(4/5) by 1
user
|
10/12/11 |
Getting Started With the PSoC Microcontroller
How do I get started with PSoC?
|
Not yet rated
|
10/12/11 |
External 32K crystal oscillator availability in PSoC1 family
|
Not yet rated
|
07/13/11 |
FLASH Checksum calculation
How can I execute a FLASH Checksum operation in user code?
|
Not yet rated
|
07/12/11 |
How do I Couple an AC Sine Wave Into the PSoC?
How do I Couple an AC Sine Wave Into the PSoC?
|
Not yet rated
|
06/27/11 |
Displaying a Floating Point Number
How to display a floating point number on the LCD when using the PSoC C-compiler?
|
(3.7/5) by 3
users
|
06/27/11 |
Connecting an Analog Signal on P0[x] to an ADC
How do I connect a signal from and analog input pin on Port0 to an ADC?
|
Not yet rated
|
06/26/11 |
Analog ground not getting connected at output pin.
Why can't I get Analog Ground at the output pin even if I configure TestMux for the same, though I get RefHi and RefLo at the output in PSoC1 ?
|
Not yet rated
|
06/26/11 |
CY3240-I2C-USB Bridge used to program PSoC device.
Can I use the CY3240 I2C-USB Bridge to program a PSoC?
|
Not yet rated
|
06/19/11 |
1-Wire Communication - Pull Up Resistor
Is an external pull up resistor required in 1-wire communication?
|
Not yet rated
|
06/13/11 |
Can't Acquire Device - Error while Programming PSoC1
How do I correct the error message "Can't acquire device?"
|
Not yet rated
|
06/12/11 |
Enable MAC in Compiler Does Not Work
I cannot get the enable MAC to work.
|
Not yet rated
|
06/12/11 |
Build error - LMM info: 'Interrupt RAM' uses too many bytes
When I try to compile my project in PSoC Designer, I get the message:
Build error. LMM info: 'Interrupt RAM' uses 39 bytes in page 0.
and my project does not compile.
What do I need to do to make this work correctly?
|
Not yet rated
|
06/12/11 |
Accidental Modification of I/O Pins in PSoC1
I am unable to modify the state of a PSoC pin using instructions like PRTxDR |= 0x01, PRTxDR &= ~0x01. What am I doing wrong?
|
Not yet rated
|
06/12/11 |
DAC8 as Reference to a PGA
I am using the output of a DAC8 as reference to a PGA, but it does not work. What could be the reason?
|
(4/5) by 1
user
|
06/12/11 |
Difference between Factory Programmable and Field Programmable devices
What is the difference between Factory Programmable and Field Programmable devices?
|
Not yet rated
|
06/12/11 |
Change the "Select" type for pins in PSoC Designer firmware
How can I switch between "StdCPU" to "Global In" or "Global Out" bus within firmware?
|
Not yet rated
|
06/12/11 |
Glitch on the I2C Lines During Power Up
Why is there a glich on the I2C lines during Power On or Reset? How can this be removed?
|
(3/5) by 1
user
|
05/29/11 |
Bandwidth of Continuous Time Operation Amplifier of CY8C26xxx/CY8C25xxx and CY8C27xxx.
What is the bandwidth of a continuous time op-amp?
|
Not yet rated
|
05/29/11 |
Calibrate the PSoC Internal Temperature Sensor
How do you calibrate the temperature of the FlashTemp user module?
|
Not yet rated
|
05/29/11 |
Advantage of multiple stop bits at Transmitter side for all PSoC devices
What is the recommended number of stop bits for UART transmitter?
|
Not yet rated
|
05/24/11 |
Comparator Bus as Clock Input to Timer
|
Not yet rated
|
03/30/11 |