Cypress Perform

Home > Design Support > Cypress Developer CommunityTM > Cypress Forums > PSoC® 3 > problem in Programming CY8cKit-030

Bookmark and Share
Cypress Developer CommunityTM
Forums | Videos | Blogs | Training | Rewards Program | Community Components



problem in Programming CY8cKit-030
Moderator:
RKRM

Post Reply
Follow this topic



problem in Programming CY8cKit-030

sivananda posted on 09 Oct 2012 1:52 AM PST
Top Contributor
58 Forum Posts

 hi...

       while iam trying to program my CY8Ckit-030, i am getting an error as    "There was an error while programming the device: PSoC Programmer reported error (102 - Failed to erase the flash)"....

        i am getting this error in both creator 2.0 and 2.1.........can any one help me how to rectify it.........

here iam attaching a screen shot of the build window.....




Re: problem in Programming CY8cKit-030

Bob Marlowe posted on 09 Oct 2012 03:29 AM PST
Top Contributor
1768 Forum Posts

Are you using the USB-Connection or a Miniprog3 to program the chip?

Any protection set for your PSoC3?

Same error (probably) for a project that earlier did program?

Also have a look here http://www.cypress.com/?app=forum&id=2233&rID=69172 although the error is a bit different.

 

Bob

 

 

 



Re: problem in Programming CY8cKit-030

sivananda posted on 09 Oct 2012 04:17 AM PST
Top Contributor
58 Forum Posts

 @Bob

                 I am using USB port to program.......i tried by disabling my bluetooth setting of laptop.....but still iam getting the same errors....

 



Re: problem in Programming CY8cKit-030

sivananda posted on 09 Oct 2012 04:20 AM PST
Top Contributor
58 Forum Posts

 i am using the latest programmer 3.16....

earlier i was using first touch kit......now also, the programming of same to the first touch kit is happening successfully....when i try the same with the Cy8cKit-030, i am unable to program.......



Re: problem in Programming CY8cKit-030

danaaknight posted on 09 Oct 2012 04:24 AM PST
Top Contributor
1773 Forum Posts

Power jumpers on the board match project settings ?

 

Regards, Dana.



Re: problem in Programming CY8cKit-030

sivananda posted on 09 Oct 2012 04:47 AM PST
Top Contributor
58 Forum Posts

ok....thank you very much............now it is programming properly............



Re: problem in Programming CY8cKit-030

sachinbvp posted on 09 Oct 2012 06:15 AM PST
Top Contributor
139 Forum Posts

I am also facing these type of error in past please change use COM port or update your software to latest to avoid these errors.






ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

Spec No: None; Sunset Owner: GRAA; Secondary Owner: RAIK; Sunset Date: 01/01/20