Cypress Perform

Home > Design Support > Cypress Developer CommunityTM > Cypress Forums > PSoC® 3 > PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station

Bookmark and Share
Cypress Developer CommunityTM
Forums | Videos | Blogs | Training | Rewards Program | Community Components



PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station
Moderator:
RKRM

Post Reply
Follow this topic



PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station

hling posted on 04 Feb 2012 12:00 PM PST
Member
8 Forum Posts

Hi,
Can someone please help me, I would like to program the CY3271-EXP1 PSoC Weather Station board by using MiniProg3 so that I can take the reading of surrounding light intensity and then sent the reading through serial comms to an application I wrote and stored the data then draw it out into a graph. May I know if this is do-able using PSoC Creator 2.0 instead of PSoC Designer?? May i know how to setup the Weather Station with the miniprog3 and how to make the Weather Station Board work? I tried to connect Pin 1,3,5,7,9 of the Weather Station Board to the Miniprog3 5-Pin Interface but when i select debug target PSoC Creator 2.0 could not detect any device.




Re: PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station

Bob Marlowe posted on 04 Feb 2012 01:26 PM PST
Top Contributor
1768 Forum Posts

It is not very helpful when you double-post your question in different forums, I'm sure you won't get better / faster answeres.

Bob



Re: PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station

U2 posted on 05 Feb 2012 07:37 AM PST
Cypress Employee
589 Forum Posts

The CY Kit 3271 is a PSoC1 based kit. PSoC Creator can be used to program PSoC3 and PSoC5 devices only. Yes you will definitely not be able to find a debug target from PSoC Creator when you connect to a 3271 because the device is not supported y the software. I believe that there is a dedicated weather monitor application associated with the kit if I am not wrong. 



Re: PSoC3 CY8CKIT-001 and CY3271-EXP1 PSoC Weather Station

hling posted on 07 Feb 2012 02:15 AM PST
Member
8 Forum Posts

Sorry about the double posting as i'm not sure where should i put my problem at. There is a dedicated software appliation that is provided to monitor the CY 32271-EXP1 and if i want to program something to it i understand that i have to use PSoC Designer. And i'm told that PSoC Designer only works with PSoC 1 and not PSoC 3. So if my development board is in PSoC 3 is there anyway things might works between PSoC3 and the CY3271-EXP1?






ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

Spec No: None; Sunset Owner: GRAA; Secondary Owner: RAIK; Sunset Date: 01/01/20