Cypress Perform

Home > Design Support > Cypress Developer CommunityTM > Cypress Forums > USB Controllers > want to output it directly to the GPIF-II data bus.

Bookmark and Share
Cypress Developer CommunityTM
Forums | Videos | Blogs | Training | Rewards Program | Community Components



want to output it directly to the GPIF-II data bus.
Moderator:
RSKV

Post Reply
Follow this topic



want to output it directly to the GPIF-II data bus.

VitaminZZ posted on 10 Oct 2012 2:12 AM PST
Senior Member
12 Forum Posts
Hello, everyone. I want to output 32 bit data directly to the GPIF-II data according to the FX3 firmware. GPIF-II is master mode. When you execute CyU3PGpifWriteDataWords( 0, CyTrue, 4, cmd, 0 ) ... ^^^^^ "Error74(CY_U3P_ERROR_FAILURE)" returns through it executed according to the following procedures. When you execute CyU3PGpifWriteDataWords( 0, CyFalse, 4, cmd, 0 ) ... ^^^^^^ "Error7(CY_U3P_ERROR_NO_EVENTS)" returns through it executed according to the following procedures. Is there a procedure for which it is insufficient what? 1,CyU3PDeviceConfigureIOMatrix(); isDQ32Bit = CyTrue; 2,CyU3PibInit(); 3,CyU3PGpifLoad(); 4,CyU3PGpifStart(); 5,CyU3PGpifWriteDataWords( 0, CyTrue, 4, cmd, 0 ); - CY_U3P_ERROR_FAILURE ERROR!! 6,CyU3PGpifControlSwInput( CyTrue ); - FW_TRIG trigeer on Control signal set by DR_GPIO is effective. Is not enabled DR_DATA. DQ[31:0] is all 0. 7,CyU3PGpifControlSwInput( CyFalse ); - FW_TRIG trigeer off My best regards.


Re: want to output it directly to the GPIF-II data bus.

VitaminZZ posted on 10 Oct 2012 02:16 AM PST
Senior Member
12 Forum Posts
Hello, everyone. I want to output 32 bit data directly to the GPIF-II data according to the FX3 firmware. GPIF-II is master mode. When you execute CyU3PGpifWriteDataWords( 0, CyTrue, 4, cmd, 0 ) ... ^^^^^ "Error74(CY_U3P_ERROR_FAILURE)" returns through it executed according to the following procedures. When you execute CyU3PGpifWriteDataWords( 0, CyFalse, 4, cmd, 0 ) ... ^^^^^^ "Error7(CY_U3P_ERROR_NO_EVENTS)" returns through it executed according to the following procedures. Is there a procedure for which it is insufficient what? 1,CyU3PDeviceConfigureIOMatrix(); isDQ32Bit = CyTrue; 2,CyU3PibInit(); 3,CyU3PGpifLoad(); 4,CyU3PGpifStart(); 5,CyU3PGpifWriteDataWords( 0, CyTrue, 4, cmd, 0 ); - CY_U3P_ERROR_FAILURE ERROR!! 6,CyU3PGpifControlSwInput( CyTrue ); - FW_TRIG trigeer on Control signal set by DR_GPIO is effective. Is not enabled DR_DATA. DQ[31:0] is all 0. 7,CyU3PGpifControlSwInput( CyFalse ); - FW_TRIG trigeer off My best regards.

Re: want to output it directly to the GPIF-II data bus.

VitaminZZ posted on 10 Oct 2012 02:21 AM PST
Senior Member
12 Forum Posts
I have mentioned in the attachment cannot be a new line.




ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.