Cypress Perform

Home > Design Support > Cypress Developer CommunityTM > Cypress Forums > USB Controllers > Debugging on Cy7C68013A

Bookmark and Share
Cypress Developer CommunityTM
Forums | Videos | Blogs | Training | Rewards Program | Community Components



Debugging on Cy7C68013A
Moderator:
RSKV

Post Reply
Follow this topic



Debugging on Cy7C68013A

giginjose posted on 01 Aug 2012 11:35 PM PST
Top Contributor
33 Forum Posts

 Hi, 

I am working on Cy7C68013A-56pin cypress USB controller. I am not using a development board, instead made a custom design for my own application. Later, I read somewhere that 56-pin doesn't support debugging. Is that right. ? Is there any way that I can do any USB based debugging on  Cy7C68013A-56pin cypress USB controller. ? Or, should I use a 100-pin  Cy7C68013A cypress USB controller for debugging purpose ? 

I am using uvision keil IDE. 

 

 

Re: Debugging on Cy7C68013A

RSKV posted on 01 Aug 2012 12:25 AM PST
Cypress Employee
655 Forum Posts

Yes. 56-pin package does not support the UART debugging. Those pins are available from 100-pin package.

You can do one thing. You can use FX2LP DVK for your firmware development as it has all debugging facilities. Once your firmware is ready then you can use the same code on your custom board.

Regards,

sai krishna.

Re: Debugging on Cy7C68013A

giginjose posted on 01 Aug 2012 12:48 AM PST
Top Contributor
33 Forum Posts

 I have a USB device interface on my board. Is there any kind of USB debugging methods available ? 

If I use a 100 pin package, will it support break point debugging and printf debugging ? 

Other than these, are there any extended debugging faclilities available on FX2LP DVK. 

Thank You

Re: Debugging on Cy7C68013A

RSKV posted on 01 Aug 2012 02:00 AM PST
Cypress Employee
655 Forum Posts

Even with the current 56-pin chip you can do break point debugging using Keil.

Yes. 100-pin package provide both options available in debugging. FX2LP DVK offers these two options (UART and break point).

Regards,

sai kirshna.

Re: Debugging on Cy7C68013A

giginjose posted on 01 Aug 2012 02:26 AM PST
Top Contributor
33 Forum Posts

 Can you help me with any documentation for break point debugging of 56-pin Cy7C68013A using keil. 

Re: Debugging on Cy7C68013A

RSKV posted on 01 Aug 2012 05:14 AM PST
Cypress Employee
655 Forum Posts

Please go through the below mentioned application note.

http://www.cypress.com/?docID=4629

Regards,

sai kirshna.



ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.