Cypress Perform

Home > Design Support > Cypress Developer CommunityTM > Cypress Forums > USB Controllers > Can not download the IMG file to SPI in "USB Control Center".

Bookmark and Share
Cypress Developer CommunityTM
Forums | Videos | Blogs | Training | Rewards Program | Community Components



Can not download the IMG file to SPI in "USB Control Center".
Moderator:
RSKV

Post Reply
Follow this topic



Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 16 Apr 2012 2:31 AM PST
Senior Member
12 Forum Posts
Please tell me the procedure. 1, DVK-SW25[4:1]=OFF,ON,OFF,OFF 2, J96 = "2-3" SHORT 3, J97 = OPEN 4, J98 = "2-3" SHORT PMODE[2:0] = "0F1" 5, Program ->FX3 -> SPI FLASH 6, "Cypress USB BootProgrammer" detected.(detect.png) 7, Program ->FX3 -> I2C EEPROM The following message is displayed. ""Bootloader is not running" dialog is "Please reset your device to download firmware." What is the mistake? Environment Windows7 Pro @64bit CyControl(1.0.0.1) CyUSB(1.0.0.1)


Re: Can not download the IMG file to SPI in "USB Control Center".

aasi posted on 17 Apr 2012 02:18 AM PST
Cypress Employee
1073 Forum Posts

The format of your post seems to have trouble. Please repost it, especially the relevant jumper, switch settings so that I can figure out what is going wrong.

Regards,

Anand

Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 17 Apr 2012 05:52 AM PST
Senior Member
12 Forum Posts
Please tell me the procedure. 1, DVK-SW25[4:1]=OFF,ON,OFF,OFF 2, J96 = "2-3" SHORT 3, J97 = OPEN 4, J98 = "2-3" SHORT 　　PMODE[2:0] is "0F1"(SPI, On Failure, USB Boot is Enabled) 5, Program ->FX3 -> SPI FLASH 6, "Cypress USB BootProgrammer" detected.(detect.png) 7, Program ->FX3 -> I2C EEPROM The following message is displayed. "Bootloader is not running" dialog is "Please reset your device to download firmware". What is the mistake? --Environment-- Windows7 Pro @64bit CyControl(1.0.0.1) CyUSB(1.0.0.1) I'm sorry. Thank you so will post again.

Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 17 Apr 2012 05:58 AM PST
Senior Member
12 Forum Posts
1,DVK-SW25[4:1]=OFF,ON,OFF,OFF 2, J96 = "2-3" SHORT

Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 17 Apr 2012 06:00 AM PST
Senior Member
12 Forum Posts
Can not be a newline. 3, J97 = OPEN 4, J98 = "2-3" SHORT PMODE[2:0] is "0F1"(SPI, On Failure, USB Boot is Enabled)

Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 17 Apr 2012 06:31 AM PST
Senior Member
12 Forum Posts 
1,DVK-SW25[4:1]=OFF,ON,OFF,OFF
2,J96 = 2-3 SHORT
3,J97 = OPEN
4,J98 = 2-3 SHORT

PMODE[2:0] is 0F1


Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 17 Apr 2012 06:34 AM PST
Senior Member
12 Forum Posts 
Please tell me the procedure.

1, DVK-SW25[4:1]=OFF,ON,OFF,OFF
2, J96 = "2-3" SHORT
3, J97 = OPEN
4, J98 = "2-3" SHORT

   PMODE[2:0] is "0F1"

5, Program ->FX3 -> SPI FLASH
6, "Cypress USB BootProgrammer" detected.(detect.png)
7, Program ->FX3 -> I2C EEPROM The following message is displayed.
"Bootloader is not running" dialog is "Please reset your device to download firmware."

What is the mistake?

--Environment--
Windows7 Pro @64bit
CyControl(1.0.0.1)
CyUSB(1.0.0.1


Re: Can not download the IMG file to SPI in "USB Control Center".

aasi posted on 19 Apr 2012 11:01 PM PST
Cypress Employee
1073 Forum Posts

Have you taken care of J101 to J104 to make sure the SPI lines are connected to the EEPROM?

Regards,

Anand

Re: Can not download the IMG file to SPI in "USB Control Center".

aasi posted on 19 Apr 2012 11:03 PM PST
Cypress Employee
1073 Forum Posts

Sorry. Got confused by the title of thread. Re-read it

Following is my understanding, if you try to program SPI EEPROM everything works fine but when you try to program I2C EEPROM it says bootloader is not running. Is my understanding right.

Re: Can not download the IMG file to SPI in "USB Control Center".

VitaminZZ posted on 19 Apr 2012 07:27 AM PST
Senior Member
12 Forum Posts
Thank you for advice. I want to programming in SPI-FLASH(U26 M25P40). There was little progress. USB2.0 host to connect. Select the IMG file is displayed as "Programming of SPI FLASH in progress...", is like being transferred. Does not end even after 30 minutes, however. J101 to J104 is All 2-3 SHORT. Please advice if there is anything else to check.




ALL CONTENT AND MATERIALS ON THIS SITE ARE PROVIDED "AS IS". CYPRESS SEMICONDUCTOR AND ITS RESPECTIVE SUPPLIERS MAKE NO REPRESENTATIONS ABOUT THE SUITABILITY OF THESE MATERIALS FOR ANY PURPOSE AND DISCLAIM ALL WARRANTIES AND CONDITIONS WITH REGARD TO THESE MATERIALS, INCLUDING BUT NOT LIMITED TO, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHT. NO LICENSE, EITHER EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, IS GRANTED BY CYPRESS SEMICONDUCTOR. USE OF THE INFORMATION ON THIS SITE MAY REQUIRE A LICENSE FROM A THIRD PARTY, OR A LICENSE FROM CYPRESS SEMICONDUCTOR.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms and Conditions of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms and Conditions of this site. Cypress Semiconductor and its suppliers reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.